Evo VIII Ecu (USDM) in Evo IV (JDM)
#16
Evolved Member
iTrader: (5)
My car don´t star!!!
I think that is the inmoviliser but I try to disable but I could not.... I don´t know how =S....
when I run ecuflash I get a read image.. but i don´t find for change the periphery codes, etc... Can you help for explain best way to understand this??'
Apologize for the inconvenience!!!!
Cheers!!!
I think that is the inmoviliser but I try to disable but I could not.... I don´t know how =S....
when I run ecuflash I get a read image.. but i don´t find for change the periphery codes, etc... Can you help for explain best way to understand this??'
Apologize for the inconvenience!!!!
Cheers!!!
1)Close Ecuflash
2) Add the xml to your xml in the evo rommetadata folder
3) Goto the periphery settings and set immobilizer bit to 0
4) Flash car
#17
Yeahh, I tried to do that but when I go to the periphery setting it´s not avalibable...
#19
Finally, I could not start the engine, but I eliminated the inmovilizer. The Ecu it´s ok, the car tried to start, but, when I scanned the Ecu, it gave to me the P0340 code, so, It´s the cam sensor position.
Today, I will change it and I hope that everything goes out well and the car start!!!!
the I tell you guys how it goes!!!
#20
Evolved Member
iTrader: (5)
Thank you to all, really, thank you very much!!
Finally, I could not start the engine, but I eliminated the inmovilizer. The Ecu it´s ok, the car tried to start, but, when I scanned the Ecu, it gave to me the P0340 code, so, It´s the cam sensor position.
Today, I will change it and I hope that everything goes out well and the car start!!!!
the I tell you guys how it goes!!!
Finally, I could not start the engine, but I eliminated the inmovilizer. The Ecu it´s ok, the car tried to start, but, when I scanned the Ecu, it gave to me the P0340 code, so, It´s the cam sensor position.
Today, I will change it and I hope that everything goes out well and the car start!!!!
the I tell you guys how it goes!!!
#21
The car finally start =). But the CEL and other light it´s on! but I don´t care =).
i have another map (for race) but only the HEX not XML and I want to install to my car, how can I do????
i have another map (for race) but only the HEX not XML and I want to install to my car, how can I do????
#23
#24
Evolved Member
iTrader: (10)
the red warning light is the cat overheat light it's not supported on the newer roms , so either join the wires to the sensor (under the drivers seat ) or take the bulb out of the dash , it has no other purpose than to tell you if the cat gets too hot , it was discontinued after the evo4 .
#28
Evolving Member
iTrader: (13)
Send me your mods or specs that have your Evo, maf, injectors, etc etc. this is my email: jonmorera@hotmail.com I can make a rom with no inmobilizer and stocks maps to start your Evo.
#29
Evolved Member
iTrader: (8)
Join Date: Nov 2010
Location: Georgia
Posts: 752
Likes: 0
Received 0 Likes
on
0 Posts
bumping this thread up. got jdm E4 with swapped VIII ecu and rear screen defroster doesn't work. is it something ecu/connection related or shoud I look for the problem somewhere else ?
when turning rear defroster on/off there's slight ticking sound somewhere from under steering wheel. does that rule out ecu/wiring problem and I can say it's turning on but no power reaches till rear screen ?
when turning rear defroster on/off there's slight ticking sound somewhere from under steering wheel. does that rule out ecu/wiring problem and I can say it's turning on but no power reaches till rear screen ?