Scaling Omni 4bar MAP for JDM E7.
#1
Evolved Member
Thread Starter
Scaling Omni 4bar MAP for JDM E7.
Hey guys,
Gonna install my newly received Omni 4-bar map sensor later tonight on my car, have reviewed all the scaling mods by 'mrfred' (legend) and all relate to USDM cars.
I'm going to try the 2003 E8 code below and see how that goes, but does anyone before I do it have any exprience throwing them onto an E7?
I'm running 90550001 btw.
Cheers.
--------------------
mrfred's code for USDM '03 E8.
Gonna install my newly received Omni 4-bar map sensor later tonight on my car, have reviewed all the scaling mods by 'mrfred' (legend) and all relate to USDM cars.
I'm going to try the 2003 E8 code below and see how that goes, but does anyone before I do it have any exprience throwing them onto an E7?
I'm running 90550001 btw.
Cheers.
--------------------
mrfred's code for USDM '03 E8.
ROM Mods for 2003 USDM Evo 8 ROM 94170008
First is to add some definitions to your ECUFlash ROM XML definition file found in:
C:\Program Files\OpenECU\EcuFlash\rommetadata\mitsubishi\evo
Open the 94170008.xml file with the text/XML editor of your choice. Scroll down to the bottom of the file. Add the following lines just before the </rom> tag (copy everything *between* the ----):
----
<table name="MAP Test 1: Mid VE Max Voltage" category="MAPSensor" address="2048" type="1D" level="1" scaling="Volts16"/>
<table name="MAP Test 1: Mid VE Min Voltage" category="MAPSensor" address="2046" type="1D" level="1" scaling="Volts16"/>
<table name="MAP Test 2: Low VE Max Voltage" category="MAPSensor" address="204C" type="1D" level="1" scaling="Volts16"/>
<table name="MAP Test 3: High VE Min Voltage" category="MAPSensor" address="2050" type="1D" level="1" scaling="Volts16"/>
----
After modifying and saving the ROM xml file, launch ECUFlash, open your ROM, and find the new entries. Note that they have their own category. It may be necessary to set ECUFlash to "Developer" mode in the ECUFlash options (and relaunch ECUFlash) to be able to see the tables. Here is what needs to be changed in ECUFlash:
MAP Test 1: Mid VE High Voltage Test -- Change from 4.61 volts to 4.90 volts.
MAP Test 1: Mid VE Low Voltage Test -- Change from 0.10 volts to 0.06 volts.
MAP Test 3: High VE Voltage Test -- Change from 1.80 volts to 0.51 volts.
In ECUFlash, find the "Periphery2 (FCA) Bits" table. Change bit.9 from 1 to 0. Use the "minus" key on the keyboard. This disables the P0401 (EGR) test.
Save the ROM file, and flash your ECU with it. That's it for the ROM mods. Now skip down to the end of this post to see instructions for setting up EvoScan/Mitsulogger to log boost.
First is to add some definitions to your ECUFlash ROM XML definition file found in:
C:\Program Files\OpenECU\EcuFlash\rommetadata\mitsubishi\evo
Open the 94170008.xml file with the text/XML editor of your choice. Scroll down to the bottom of the file. Add the following lines just before the </rom> tag (copy everything *between* the ----):
----
<table name="MAP Test 1: Mid VE Max Voltage" category="MAPSensor" address="2048" type="1D" level="1" scaling="Volts16"/>
<table name="MAP Test 1: Mid VE Min Voltage" category="MAPSensor" address="2046" type="1D" level="1" scaling="Volts16"/>
<table name="MAP Test 2: Low VE Max Voltage" category="MAPSensor" address="204C" type="1D" level="1" scaling="Volts16"/>
<table name="MAP Test 3: High VE Min Voltage" category="MAPSensor" address="2050" type="1D" level="1" scaling="Volts16"/>
----
After modifying and saving the ROM xml file, launch ECUFlash, open your ROM, and find the new entries. Note that they have their own category. It may be necessary to set ECUFlash to "Developer" mode in the ECUFlash options (and relaunch ECUFlash) to be able to see the tables. Here is what needs to be changed in ECUFlash:
MAP Test 1: Mid VE High Voltage Test -- Change from 4.61 volts to 4.90 volts.
MAP Test 1: Mid VE Low Voltage Test -- Change from 0.10 volts to 0.06 volts.
MAP Test 3: High VE Voltage Test -- Change from 1.80 volts to 0.51 volts.
In ECUFlash, find the "Periphery2 (FCA) Bits" table. Change bit.9 from 1 to 0. Use the "minus" key on the keyboard. This disables the P0401 (EGR) test.
Save the ROM file, and flash your ECU with it. That's it for the ROM mods. Now skip down to the end of this post to see instructions for setting up EvoScan/Mitsulogger to log boost.
#2
Evolving Member
Join Date: Apr 2008
Location: New Zealand
Posts: 462
Likes: 0
Received 0 Likes
on
0 Posts
Hey guys,
Gonna install my newly received Omni 4-bar map sensor later tonight on my car, have reviewed all the scaling mods by 'mrfred' (legend) and all relate to USDM cars.
I'm going to try the 2003 E8 code below and see how that goes, but does anyone before I do it have any exprience throwing them onto an E7?
I'm running 90550001 btw.
Cheers.
--------------------
mrfred's code for USDM '03 E8.
Gonna install my newly received Omni 4-bar map sensor later tonight on my car, have reviewed all the scaling mods by 'mrfred' (legend) and all relate to USDM cars.
I'm going to try the 2003 E8 code below and see how that goes, but does anyone before I do it have any exprience throwing them onto an E7?
I'm running 90550001 btw.
Cheers.
--------------------
mrfred's code for USDM '03 E8.
#5
Evolved Member
Thread Starter
MAP Test 1: Mid VE Max Voltage Test -- Change from 4.61 volts to 4.90 volts.
MAP Test 1: Mid VE Min Voltage Test -- Change from 0.10 volts to 0.06 volts.
MAP Test 3: Low VE Max Voltage Test -- Change to 4.20 volts.
MAP Test 4: High VE Min Voltage Test -- Change from 1.80 volts to 0.51 volts.
MAP Test 1: Mid VE Min Voltage Test -- Change from 0.10 volts to 0.06 volts.
MAP Test 3: Low VE Max Voltage Test -- Change to 4.20 volts.
MAP Test 4: High VE Min Voltage Test -- Change from 1.80 volts to 0.51 volts.
#6
Newbie
Join Date: Nov 2010
Location: Auckland, New Zealand
Posts: 83
Likes: 0
Received 0 Likes
on
0 Posts
MAP Test 1: Mid VE Max Voltage Test -- Change from 4.61 volts to 4.90 volts.
MAP Test 1: Mid VE Min Voltage Test -- Change from 0.10 volts to 0.06 volts.
MAP Test 3: Low VE Max Voltage Test -- Change to 4.20 volts.
MAP Test 4: High VE Min Voltage Test -- Change from 1.80 volts to 0.51 volts.
MAP Test 1: Mid VE Min Voltage Test -- Change from 0.10 volts to 0.06 volts.
MAP Test 3: Low VE Max Voltage Test -- Change to 4.20 volts.
MAP Test 4: High VE Min Voltage Test -- Change from 1.80 volts to 0.51 volts.
Trending Topics
#9
Evolved Member
It is a bit of noobish question but what will this code do ?
-- I dont have this code defined in my e7 rom , what will happen if we dont put this in our xml ?
using 96534..
-- I dont have this code defined in my e7 rom , what will happen if we dont put this in our xml ?
using 96534..
Thread
Thread Starter
Forum
Replies
Last Post
mrfred
ECU Flash
268
Feb 26, 2022 06:16 PM