New headlights on the block
#169
Evolving Member
Check out this quad set in action:
Specs:
* OEM Single Xenon projector replaced with an FX-R BiXenon projector.
* Morimoto 50w ballast
* Morimoto 50w D2S bulb (4300K)
Camera:
Cannon 7D set to auto (No flash)
Note: Pix may depict brighter output than they really are.
WALL SHOTS
HIGH BEAM
LHS projector needs to be adjusted down:
ROAD SHOTS:
HIGH BEAM:
STREET SHOTS:
HIGH BEAM:
ROLLING SHOTS:
#171
Check out this quad set in action:
Specs:
* OEM Single Xenon projector replaced with an FX-R BiXenon projector.
* Morimoto 50w ballast
* Morimoto 50w D2S bulb (4300K)
Camera:
Cannon 7D set to auto (No flash)
Note: Pix may depict brighter output than they really are.
<redacted images -llDemonll>
Last edited by llDemonll; Feb 12, 2017 at 08:29 AM.
#173
Evolved Member
iTrader: (11)
bumping this seriously old thread.
I just bought a set of jdm hid headlights for my evo ix
I need to swap projectors because I don't want a jdm projector to be used in america
Has anyone done anything similar to this with the newer stuff available? I plan on doing a rebuild of these lights from head to toe
I just bought a set of jdm hid headlights for my evo ix
I need to swap projectors because I don't want a jdm projector to be used in america
Has anyone done anything similar to this with the newer stuff available? I plan on doing a rebuild of these lights from head to toe
#174
Evolving Member
iTrader: (5)
bumping this seriously old thread.
I just bought a set of jdm hid headlights for my evo ix
I need to swap projectors because I don't want a jdm projector to be used in america
Has anyone done anything similar to this with the newer stuff available? I plan on doing a rebuild of these lights from head to toe
I just bought a set of jdm hid headlights for my evo ix
I need to swap projectors because I don't want a jdm projector to be used in america
Has anyone done anything similar to this with the newer stuff available? I plan on doing a rebuild of these lights from head to toe
The following users liked this post:
EVO196 (Apr 7, 2020)
#175
Evolved Member
iTrader: (11)
Honestly, I am rather addicted to the idea of changing the setup in the high beam and fog light projector as well. The difficult part is that the high beam is very shallow, and the fog light is small. I plan on painting the trim grey to match the body. I will also be doing something with LEDs for the running light/parking light/signal setup. I have my heart set on 3D printing ABS mounts for LED PCB's inside (like I did with my custom tail lights I built)
#176
Evolved Member
iTrader: (11)
Evil-Evo, did you do your own projector swap? I have everything apart, and I am looking at the HID projector adjuster motor. It snaps through the back and engages into the back of the bracket that the HID projector mounts too... I am not sure what is the best way to snap this off and I was looking for a photo or something that makes this clear...
#177
Evolving Member
Evil-Evo, did you do your own projector swap? I have everything apart, and I am looking at the HID projector adjuster motor. It snaps through the back and engages into the back of the bracket that the HID projector mounts too... I am not sure what is the best way to snap this off and I was looking for a photo or something that makes this clear...
#179
Evolving Member
Thread
Thread Starter
Forum
Replies
Last Post
mRVRsport
Outlander Sport
968
Feb 25, 2021 11:58 AM
evotuner04
For Sale/WTB - Engine / Drivetrain / Power
14
Nov 24, 2016 03:41 PM
WTT[Canadianl]: Cusco RS Front LSD for Evo VIII/IX with ACD
RS200
For Sale/WTB - Engine / Drivetrain / Power
3
May 27, 2016 10:52 PM