96530706 f52 96530706 Mitsubishi TDM Lancer Evolution VIII 6MT 2005 mitsukernel SH7052

Value

Enable Valet Mode :+ Enable Auto-Valet on Fresh Ignition :Enable Alternate Maps Master ADC0F=1,AutoICS=2,TPS=3 :Restore ICS State on Ignition :Flash ICS when on Alternate Map :Flash CEL on Knock :+ Drop Boost on High-Knock :Enable Manual ICS Linger :Enable Spray ICS on Knock :Enable No Lift to Shift :Enable RearO2 Simulator :Enable Manifold Absolute Pressure Averaging :Enable WB02 Check AFR Safety :+ Drop Boost on AFR Out of Range :Enable AirFlow Calcs :Enable Launch Maps :

CEL will flash SLOWLY once KnockSum exceeds this value:

CEL will flash QUICKLY once KnockSum exceeds this value:

Load must EXCEED this value before 'CEL on Knock' activates:

Duration CEL continues to flash AFTER the last occurance has stopped:

Maximum RPM allowed when Valet Mode is activated:

Duration TPS must be held at 100% to activate/de-activate Valet Mode:

Duration CEL continues to flash after Valet Mode is activaed/de-activated:

KNOCK SUM must MEET or EXCEED this value to activate 'Spray on Knock':

Load must exceed this value to allow 'Spray on Knock' to activate:

Duration ICS continues to spray AFTER knock goes below 'KnockSUM Required for Spray':

Maximum amount RPM will drop once NLTS is activated:

Throttle position percentage that must be exceeded to activate NLTS:

Vehicle speed must be UNDER this value to allow NLTS to be activated:

LOAD must be UNDER this value for NLTS to be allowed to activate:

Load must exceed this value to allow AFR Safety Monitoring to lower WGDC to 0% (ECU Controlled Boost only):

WBo2 0-5v Input Voltage must exceed this value to lower WGDC to 0% (ECU controlled boost only):

Duration WGDC stays at 0% (and CEL flashes) after MAX AFR Volts return below threshold:

Duration MAX AFR volts must be exceeded before WGDC is switched to 0%:

Duration ICS sprays after MANUAL ICS button is released:

Delay Time before Alt Maps engage once activated:

Alt Maps cannot be activated if LOAD has already exceeded:

To Activate Alt Maps,ADC0F Voltage Input Must Exceed:

To use "Fuel Cut Load x1" = 0x6DDD To use "Fuel Cut Load x2" = 0x4D00 :

FUEL CUT will not engage until the limit has been exceeded for this duration of time:

0.0160.0480.0800.1120.1440.1760.2080.2400.2720.3040.3360.3680.4000.4320.4640.4960.5280.5600.5920.6240.6560.6880.7200.7520.7840.8160.8480.8800.9120.9440.9761.0081.0401.0721.1041.1361.1681.2001.2321.2641.2961.3281.3601.3921.4241.4561.4881.5201.5521.5841.6161.6481.6801.7121.7441.7761.8081.8401.8721.9041.9361.9682.0002.0322.0642.096

Closed-Loop I-Gain After Fuel-Cut, Decrease Fuel IPW (Lean)Closed-Loop I-Gain After Fuel-Cut, Increase Fuel IPW (Rich)Closed-Loop I-Gain Idle, Decrease Fuel IPW (Lean)Closed-Loop I-Gain Idle, Increase Fuel IPW (Rich)

HiLo

Low -> MidMid -> LowMid -> HighHigh -> Mid

0.0%1.6%3.1%4.7%6.3%7.8%9.4%11.0%12.5%

0.0000.0220.0440.0660.0880.1100.1320.1540.1760.1980.2200.2420.2640.2860.3080.3300.3520.3740.3960.418

WGDC stays set at 100% until this load value is exceeded:

(Adjustable from 1-10) 1=most frequent WGDC correction intervals, 10=least frequent:

(Adjustable from 1-10) 1= most frequent WGDC correction intervals 10= Least frequent :

Reactivate OnReactivate OffDeactivate OnDeactivate Off

Throttle position must exceed this percentage to activate Launch Maps:

Vehicle speed must be BELOW this value to activate Launch Maps:

NeutDriveNeutDrive

SensitivityTiming LimitUntested

AC OffAC On

Limiter activated when above:Limiter deactivated when below:

Maximum RPM engine can achieve under ANY condtions:

Maximum RPM engine can achieve while the vehicle is STATIONARY:

0x0040 for 2003 or 0x0055 for 2004 or 0x0058 for 2005 USDM - 0x004D for EDM:

b1b2b3b4

Disable rear o2 heater by changing 0x4A0B to 0x0009:

N/AN/AN/AN/ARear O2 Heater CEL EnableN/AN/AN/A

Hex16

A8F8A8FAA8FCA8FEA900A902A904A906A908A90A

Hex16

14DB414DB614DB814DBA14DBC14DBE14DC014DC2

Hex16

36980369823698436986369883698A3698C3698E36990369923699436996369983699A3699C3699E369A0369A2369A4369A6369A8369AA369AC369AE369B0369B2369B4369B6369B8369BA369BC369BE369C0369C2369C4369C6369C8369CA369CC369CE

Hex16

369D0369D2369D4369D6369D8369DA369DC369DE369E0369E2369E4369E6369E8369EA369EC369EE369F0369F2369F4369F6369F8369FA369FC369FE36A0036A0236A0436A0636A0836A0A36A0C36A0E36A1036A1236A1436A1636A1836A1A36A1C36A1E

Hex16

36A2036A2236A2436A2636A2836A2A36A2C36A2E36A3036A3236A3436A3636A3836A3A36A3C36A3E36A4036A42

Hex16

36A4436A4636A4836A4A36A4C36A4E36A5036A5236A5436A5636A5836A5A36A5C36A5E36A6036A62

Hex16

2C702C722C742C762C78

Hex16

2D702D722D742D76

Hex16

1032C1032E10330103321033410336103381033A1033C1033E10340103421034410346103481034A

Hex16

3EFA03EFA23EFA43EFA63EFA83EFAA3EFAC3EFAE3EFB03EFB23EFB43EFB63EFB83EFBA3EFBC3EFBE3EFC03EFC23EFC43EFC63EFC83EFCA3EFCC3EFCE3EFD03EFD23EFD43EFD63EFD83EFDA3EFDC3EFDE3EFE03EFE23EFE43EFE63EFE83EFEA3EFEC3EFEE3EFF03EFF2

On TimeOff Time

OnOff

8000400020001000800400200100804020108421

000102030405060708090A0B0C0D0E0F

Stock Setting= 0x4019 Forced PASS Inpection Setting= 0xE000 :

Stock Setting= 0x6AA1 Forced PASS Inspection= 0xEAE5 :

Stock Setting= 0xDA57 Forced PASS Inspection= 0xEAFF :Stock Setting= 0x6AA1 Forced PASS Inspection= 0x6AA7 :

EGR systemOxygen heater sensorOxygen sensorA/C system refrigerantSecondary air systemEvaporative systemHeated catalystCatalyst

Off -> LowLow -> High

OnOff

Main Fan 0-12mphA/C Fan 0-12mphMain+A/C 0-12mph

Main Fan 12-31mphMain Fan 31-50mphMain Fan 50->>mphA/C Fan 12-31mphA/C Fan 31-50mphA/C Fan 50->>mphMain+A/C 12-31mphMain+A/C 31-50mphMain+A/C 50->>mph

bit.15: -bit.14: -bit.13: -bit.12: -bit.11: -bit.10: -bit.09: -bit.08: -bit.07: -bit.06: -bit.05: -bit.04: -bit.03: -bit.02: -bit.01: -bit.00: -

bit.15: -bit.14: Front o2 sensor heater circuit -bit.13: -bit.12: -bit.11: Enable EGR Duty = 100% when CTS Less Than 68C -bit.10: Timing knockdown on light acceleration and less than 3000rpm -bit.09: Enable Warmup Ign Retard -bit.08: -bit.07: Enable High Oct Ign Map Lookup (and many other subroutines) -bit.06: Enable Speed Limit Test -bit.05: -bit.04: Allow closed loop -bit.02: Enable immobilizer -bit.02: -bit.01: Rear o2 -bit.00: -

bit.15: -bit.14: -bit.13: -bit.12: -bit.11: -bit.10: -bit.09: -bit.08: -bit.07: -bit.06: -bit.05: 2nd thermo fan table -bit.04: -bit.03: -bit.02: -bit.01: -bit.00: Lean Spool -

bit.15: P0443, P0446, P0403, P0243, P0090, P2263 -bit.14: P0450, P0451, P0452, P0453 Evap -bit.13: P0441, P0442 Evap -bit.12: -bit.11: P0031, P0032, P0037, P0038 -bit.10: P1400 MAP Sensor -bit.09: P0401 EGR Test -bit.08: P0506, P0507 Idle Test -bit.07: P0170 (P0171, P0172) -bit.06: P0134 Front O2 -bit.05: P0300; set bit.4 and bit.5 to 0 to disable -bit.04: P0300; set bit.4 and bit.5 to 0 to disable -bit.03: P0132, P0136 O2 -bit.02: P0133, P0159 -bit.01: P0421 not in FSM -bit.00: -

bit.15: P0128 CT Below Reg -bit.14: P1603 Battery Backup -bit.13: -bit.12: -bit.11: P0180 - P0183, P0461, P2066 Fuel Sensors -bit.10: -bit.09: -bit.08: -bit.07: P0551 PS Pressure -bit.06: P0500 Speed Sens -bit.05: -bit.04: -bit.03: -bit.02: P0234, P0243, P2263 -bit.01: P0510 not in FSM -bit.00: P1715, P1750, etc -

bit.15: P0140 Rear O2 No Act -bit.14: P0069 MAP vs Baro -bit.13: P0111 IAT Circuit -bit.12: P0554 PS Press Sensor -bit.11: P1530 A/C1 Switch -bit.10: -bit.09: -bit.08: P0830 Clutch Pedal Circuit -bit.07: P0090 Fuel Pressure Circuit -bit.06: -bit.05: -bit.04: -bit.03: -bit.02: -bit.01: -bit.00: -

0123456789ABCDEF

MUT0XMUT1XMUT2XMUT3XMUT4XMUT5XMUT6XMUT7XMUT8XMUT9XMUTAXMUTBXMUTCXMUTDXMUTEXMUTFXMUT10XMUT11XMUT12XMUT13XMUT14XMUT15XMUT16XMUT17XMUT18XMUT19XMUT1AXMUT1BXMUT1CXMUT1DX

024487295119143167191215238262286