log boost with JDM MAP sensor (updated instructions)
Feb 19, 2011, 03:59 PM
#781
Zeitronix 3.5Bar settings:
Map test 1: Mid VE max voltage = 4.90
Map test 1: Mid VE min voltage = 0.10
Map test 2: Low VE Max Voltage = 4.90
Map test 3: High VE Min Voltage = 0.51
Map test 4: Max minus Min = 0.51
MAP Scaling for Baro = 175
EGR Pressure Diff = 0.03
EGR Map check 1 & 2:
RPM | Value
750 - 84
1000 - 84
1250 - 73
1500 - 65
1750 - 60
2000 - 55
2500 - 48
3000 - 43
3500 - 23
Map test 1: Mid VE max voltage = 4.90
Map test 1: Mid VE min voltage = 0.10
Map test 2: Low VE Max Voltage = 4.90
Map test 3: High VE Min Voltage = 0.51
Map test 4: Max minus Min = 0.51
MAP Scaling for Baro = 175
EGR Pressure Diff = 0.03
EGR Map check 1 & 2:
RPM | Value
750 - 84
1000 - 84
1250 - 73
1500 - 65
1750 - 60
2000 - 55
2500 - 48
3000 - 43
3500 - 23
0.51 20
0.90 40
1.29 57
1.68 78
2.07 97
2.46 117
2.85 138
3.24 158
3.63 255
0.90 40
1.29 57
1.68 78
2.07 97
2.46 117
2.85 138
3.24 158
3.63 255
can someone help thanks!
Aug 30, 2011, 02:30 PM
#782
Newbie
iTrader: (2)
Join Date: Nov 2010
Location: Winnipeg MB Canada
Posts: 74
Likes: 0
Received 0 Likes
on
0 Posts
Boost log issue
Hey guys,
Not sure if I should have created a new thread rather than replying to this but I'm having a problem getting full boost log. I purchased a JDM 3BAR map sensor off eBay. Installed the sensor and performed the above changes to my ECU and flashed (ECU 88590015)
Made the modification in EvoScan for 0.19347*x-14.3 (I am at 800ft)
However on multiple runs and logs the most I have ever logged was 13.9psi, which seems to me like its only reading as a 1 BAR map sensor....
However if that was the case wouldn't I have problems with my car even running or CEL with the changes I made to the ECU?
I have triple checked all the changes from this post and that I entered the correct values. I have a ProSport boost guage, doing a pull in 5th gear the gauge displayed 18-20psi but EvoScan only recorded 13.x psi
Any suggestions? Did I get sold a bogus 1 BAR map?
Not sure if I should have created a new thread rather than replying to this but I'm having a problem getting full boost log. I purchased a JDM 3BAR map sensor off eBay. Installed the sensor and performed the above changes to my ECU and flashed (ECU 88590015)
Made the modification in EvoScan for 0.19347*x-14.3 (I am at 800ft)
However on multiple runs and logs the most I have ever logged was 13.9psi, which seems to me like its only reading as a 1 BAR map sensor....
However if that was the case wouldn't I have problems with my car even running or CEL with the changes I made to the ECU?
I have triple checked all the changes from this post and that I entered the correct values. I have a ProSport boost guage, doing a pull in 5th gear the gauge displayed 18-20psi but EvoScan only recorded 13.x psi
Any suggestions? Did I get sold a bogus 1 BAR map?
Aug 30, 2011, 04:01 PM
#783
Evolved Member
iTrader: (7)
Join Date: Sep 2003
Location: Austin, Tx
Posts: 1,509
Likes: 0
Received 0 Likes
on
0 Posts
Well...it would be a 2 bar sensor if anything, because it measures from -14.7 up to 0 (1bar) then from 0 up to 14 or whatever (2nd bar). Still...that doesn't really make a lot of sense, what's your boost gauge read compared to the MAP sensor at idle?
Aug 31, 2011, 01:42 AM
#785
Evolving Member
iTrader: (15)
Join Date: Oct 2010
Location: L.I. New York
Posts: 402
Likes: 0
Received 0 Likes
on
0 Posts
If you're talking about the MAP sensor VE and stuff like that, you don't need to make any changes to the 9653 rom. It's from a car version, like European or something, that doesn't have a MAP sensor, and it doesn't use it to make any calculations. So, basically, put whatever MAP sensor in that you want with the 9653 ROM, and the only specifics you need are what you'll put in to EvoScan to scale the data properly.
I'm still a little lost with your explanation. Can you please clarify, what needs to be done to get this to work with.
I'm using
TephraMOD-96530706-v7.xml
I see a scaling in definition.
<scaling name="PSIa8 JDM3barMAP" units="PSIa" toexpr="x/(5.18*2)" frexpr="x*(2*5.18)" format="%.1f" min="0" max="24.6" inc="0.1" storagetype="uint8" endian="big"/>
do I need to edit 96530706.xml and create tables from op?
thanks
Aug 31, 2011, 07:18 AM
#786
Evolved Member
iTrader: (7)
Join Date: Sep 2003
Location: Austin, Tx
Posts: 1,509
Likes: 0
Received 0 Likes
on
0 Posts
I'm still a little lost with your explanation. Can you please clarify, what needs to be done to get this to work with.
I'm using
TephraMOD-96530706-v7.xml
I see a scaling in definition.
<scaling name="PSIa8 JDM3barMAP" units="PSIa" toexpr="x/(5.18*2)" frexpr="x*(2*5.18)" format="%.1f" min="0" max="24.6" inc="0.1" storagetype="uint8" endian="big"/>
do I need to edit 96530706.xml and create tables from op?
thanks
I'm using
TephraMOD-96530706-v7.xml
I see a scaling in definition.
<scaling name="PSIa8 JDM3barMAP" units="PSIa" toexpr="x/(5.18*2)" frexpr="x*(2*5.18)" format="%.1f" min="0" max="24.6" inc="0.1" storagetype="uint8" endian="big"/>
do I need to edit 96530706.xml and create tables from op?
thanks
Feb 6, 2012, 12:40 PM
#790
When using ROM ID: 88590015 and trying to change all the values from the USDM to the JDM values:
0.51 20
0.90 40
1.29 57
1.68 78
2.07 97
2.46 117
2.85 138
3.24 158
3.63 255
I have an issue setting the some voltage in the tenth value. This is the closest Im allowed to choose. When trying to manually set the value; it defaults to the closest lower value;
0.51 20
0.90 40
1.29 57
1.68(1.67) 78
2.07(2.07) 97
2.46(2.45) 117
2.85(2.84) 138
3.24 158
3.63 255
How safe would it be to set it to the higher value:
0.51 20
0.90 40
1.29 57
1.68(1.69) 78
2.07(2.08) 97
2.46(2.47) 117
2.85(2.86) 138
3.24 158
3.63 255
I also have an issue seeting the MAP Comparison table. It only takes 14.5 or 14.7
Or is there a way to tweak it to the correct exact value: PLEASE HELP!
0.51 20
0.90 40
1.29 57
1.68 78
2.07 97
2.46 117
2.85 138
3.24 158
3.63 255
I have an issue setting the some voltage in the tenth value. This is the closest Im allowed to choose. When trying to manually set the value; it defaults to the closest lower value;
0.51 20
0.90 40
1.29 57
1.68(1.67) 78
2.07(2.07) 97
2.46(2.45) 117
2.85(2.84) 138
3.24 158
3.63 255
How safe would it be to set it to the higher value:
0.51 20
0.90 40
1.29 57
1.68(1.69) 78
2.07(2.08) 97
2.46(2.47) 117
2.85(2.86) 138
3.24 158
3.63 255
I also have an issue seeting the MAP Comparison table. It only takes 14.5 or 14.7
Or is there a way to tweak it to the correct exact value: PLEASE HELP!
Feb 12, 2012, 07:43 PM
#794
Anyone know the scaling values for a Crespo 3 Bar Sensor?
http://www.ebay.com/itm/280613072372...S:1123&vxp=mtr
http://www.ebay.com/itm/280613072372...S:1123&vxp=mtr
May 30, 2012, 01:31 PM
#795
Is the Omni 4 bar settings the same as the Onmi 7 bar? I have the 7 bar, I was just wondering.
Also, is it normal for EvoScan to log positive boost at idle? There's 53 pages so reading will be time consuming, hopefully a response will be quicker. Thanks.
Also, is it normal for EvoScan to log positive boost at idle? There's 53 pages so reading will be time consuming, hopefully a response will be quicker. Thanks.
Last edited by ch53avitech; May 30, 2012 at 05:22 PM.
