ECU Swap & Immobiliser Code Issues

Reply Subscribe

Thread Tools

Search this Thread

Dec 16, 2009, 02:51 PM

#61

VGergo

Evolved Member

iTrader: (3)

Join Date: Nov 2005

Location: Hungary

Posts: 566

Likes: 0

Received 1 Like on 1 Post

Quote:

Originally Posted by RoadSpike

Patching the ECU is easy just need a way to connect it with a laptop. There are many MANY threads out there with that information just search them. Event this thread has the codes needed to disable the immobilizer in the 1st page or so.

Just editing the rom xml file the value to 56D2 and will work the evo ecu ?

that is easy thank you ! If I would put back the stock outlander ecu than evertyhing will be the same will use again the immobilisier ?

Reply Like

Dec 16, 2009, 02:54 PM

#62

VGergo

Evolved Member

iTrader: (3)

Join Date: Nov 2005

Location: Hungary

Posts: 566

Likes: 0

Received 1 Like on 1 Post

Quote:

Originally Posted by RoadSpike

The harness will be the most difficult part of the build i'm sure.

The second will be figuring out how to get the data port connected so you can even flash the ecu. I'm not sure what pins the laptop connects to.

Ohh I see. data port is near the obd connector where the white small connector in the tactrix cable plug in ?

Reply Like

Dec 16, 2009, 02:57 PM

#63

RoadSpike

Evolved Member

iTrader: (5)

Join Date: Oct 2006

Location: Sacramento, CA

Posts: 3,805

Likes: 0

Received 2 Likes on 2 Posts

Quote:

Originally Posted by VGergo

Ohh I see. data port is near the obd connector where the white small connector in the tactrix cable plug in ?

Yep that white connector is key to flashing the ECU apparently.

And no you don't edit the XML to flash the ecu the XML is merely there so you can see the place to change in the ECU. You have to open EcuFlash and download your rom first then edit the appropriate spot.

Periphery0 (FAA) to that value.

Reply Like

Dec 16, 2009, 03:02 PM

#64

VGergo

Evolved Member

iTrader: (3)

Join Date: Nov 2005

Location: Hungary

Posts: 566

Likes: 0

Received 1 Like on 1 Post

Okay I know which pins need in the outlander to flash the ecu

If i coud download the rom than I change it to the European one which doesnt use the MDP ?

anyway thank your help

I have to build my harness !

Reply Like

Dec 16, 2009, 03:06 PM

#65

RoadSpike

Evolved Member

iTrader: (5)

Join Date: Oct 2006

Location: Sacramento, CA

Posts: 3,805

Likes: 0

Received 2 Likes on 2 Posts

Quote:

Originally Posted by VGergo

Okay I know which pins need in the outlander to flash the ecu

If i coud download the rom than I change it to the European one which doesnt use the MDP ?

anyway thank your help

I have to build my harness !

Yeah you may as well use tephra's v7 rom without speed density patch for this since its a EDM rom without map sensor. Plus it has many neat tricks in it to help the car fly.

Reply Like

Dec 16, 2009, 03:12 PM

#66

VGergo

Evolved Member

iTrader: (3)

Join Date: Nov 2005

Location: Hungary

Posts: 566

Likes: 0

Received 1 Like on 1 Post

Quote:

Originally Posted by RoadSpike

Yeah you may as well use tephra's v7 rom without speed density patch for this since its a EDM rom without map sensor. Plus it has many neat tricks in it to help the car fly.

great

tephra v7 without speed density working from the MAF only ?

It will be fly !!!

Reply Like

Mar 14, 2018, 03:40 AM

#67

Wajeb G. Wahab

Newbie

Join Date: Mar 2012

Posts: 11

Likes: 2

Received 0 Likes on 0 Posts

Quote:

Originally Posted by RoadSpike

You know how to edit your rom.xml file to add a table?

<table name="(periphery 0)" category="Misc" address="faa" type="1D" level="1" scaling="Hex16"/>

Stock should be 56DA

Change to 56D2

So if my periphery 0 says 56D8 on the new ROM that I'm trying to flash on my car, I should enter that into the code?
<table name="56D8" category="Misc" address="faa" type="1D" level="1" scaling="Hex16"/>
Is that correct?