Alt Maps V7 - map switch not working
#1
Evolving Member
Thread Starter
iTrader: (15)
Join Date: Oct 2010
Location: L.I. New York
Posts: 402
Likes: 0
Received 0 Likes
on
0 Posts
Alt Maps V7 - map switch not working
Hi guys,
Trying to test Map switch functionality, seems like it's not working correctly.
Installed switch wired into ECU.
How I tested was to copy main map tables to alt map tables
I set all WGDC values to 50.
I figured I would test if alt maps if car ran lowered boost.
I turned switch on, took it around the block and feels same.
Here's how I have it set up in V7.
Does this look correct?
Trying to test Map switch functionality, seems like it's not working correctly.
Installed switch wired into ECU.
How I tested was to copy main map tables to alt map tables
I set all WGDC values to 50.
I figured I would test if alt maps if car ran lowered boost.
I turned switch on, took it around the block and feels same.
Here's how I have it set up in V7.
Does this look correct?
#2
Evolving Member
Thread Starter
iTrader: (15)
Join Date: Oct 2010
Location: L.I. New York
Posts: 402
Likes: 0
Received 0 Likes
on
0 Posts
I tried the test @ bottom of link:
http://evoecu.logic.net/wiki/TephraMod
Here's Evoscan log with car running:
Alt Map Act < 5. Looks like mine is 3, can I assume it's switching correctly?
http://evoecu.logic.net/wiki/TephraMod
Here's Evoscan log with car running:
Alt Map Act < 5. Looks like mine is 3, can I assume it's switching correctly?
#3
Evolved Member
iTrader: (19)
Join Date: Jun 2005
Location: N/A
Posts: 756
Likes: 0
Received 0 Likes
on
0 Posts
I couldnt get the alt map activation working on my car when i tried but to test it i changed injector scaling on alt maps and switched over. When i heard the car stumble over (on purpose) i knew my alt maps were working. Works like a dream with my hfs6.
#4
Evolving Member
Thread Starter
iTrader: (15)
Join Date: Oct 2010
Location: L.I. New York
Posts: 402
Likes: 0
Received 0 Likes
on
0 Posts
I figured the WGDC test would work.
I must have looked @ the ECU diagram a dozen times to make sure I tapped into the correct wires and pins. All looks OK.
I don't have a multi meter, nor do I know how to use one.
I guess that's my next test.
I must have looked @ the ECU diagram a dozen times to make sure I tapped into the correct wires and pins. All looks OK.
I don't have a multi meter, nor do I know how to use one.
I guess that's my next test.
Trending Topics
#10
Evolving Member
Thread Starter
iTrader: (15)
Join Date: Oct 2010
Location: L.I. New York
Posts: 402
Likes: 0
Received 0 Likes
on
0 Posts
tehpra, thanks for chiming in.
Do you mean enable flash ICS(1) as a test when I turn on/off map switch?
Even though I don't have ICS button, I'm assuming light will flash on the dash?
What voltage should I be getting from test(post 2) described in Wiki?
thanks
Do you mean enable flash ICS(1) as a test when I turn on/off map switch?
Even though I don't have ICS button, I'm assuming light will flash on the dash?
What voltage should I be getting from test(post 2) described in Wiki?
thanks
#12
Evolving Member
Thread Starter
iTrader: (15)
Join Date: Oct 2010
Location: L.I. New York
Posts: 402
Likes: 0
Received 0 Likes
on
0 Posts
I figured light would be on dash regardless on having ICS switch. The only problem is I need a way to activate/inactivate. That's why I installed the switch.
I'm getting power to switch. Toggle LED light on/off works.
I must have checked for correct ECU pin wiring 10 times...
I'm getting power to switch. Toggle LED light on/off works.
I must have checked for correct ECU pin wiring 10 times...