EvolutionM - Mitsubishi Lancer and Lancer Evolution Community

Notices

A bunch of load calculation related maps

   
Old May 6, 2014, 01:39 PM
  #61  
Evolved Member
iTrader: (9)
 
itzwolf's Avatar
 
Join Date: Mar 2005
Location: Florida
Posts: 1,193
Likes: 0
Received 2 Likes on 2 Posts
Had a little time today so gave the 3xMAP tables use actual MAP, not averaged digging a go. I haven't tried any of these so as always proceed with caution and hopefully tephra wouldn't mind confirming.

Enjoy!

52680024:

Code:
<table name="3xMAP tables use actual MAP, not averaged 0xC78A -> 0xC6DE" category="Misc" address="62a2a" type="1D" scaling="Hex16"/>
55570006:

Code:
<table name="3xMAP tables use actual MAP, not averaged 0xC79E -> 0xC6F2" category="Misc" address="62c84" type="1D" scaling="Hex16"/>
56890013:

Code:
<table name="3xMAP tables use actual MAP, not averaged 0xC7CE -> 0xC722" category="Misc" address="63474" type="1D" scaling="Hex16"/>
58010005:

Code:
<table name="3xMAP tables use actual MAP, not averaged 0xC7D6 -> 0xC72A" category="Misc" address="634b2" type="1D" scaling="Hex16"/>
59580004:

Code:
<table name="3xMAP tables use actual MAP, not averaged 0xC7DA -> 0xC72E" category="Misc" address="63446" type="1D" scaling="Hex16"/>
itzwolf is offline  
Reply Like
Old May 21, 2014, 05:48 PM
  #62  
Evolving Member
 
RS200Z's Avatar
 
Join Date: Jan 2009
Location: Singapore
Posts: 150
Received 0 Likes on 0 Posts
Originally Posted by tephra
so i tested the patch tonight, it works perfectly..

as you can see tps changes are still detected below 200 load (about 15 psi in this graphic)

but above that nothing (this is with 1 and 1 in the tps increase/decrease fields)
David, I have been testing the TPS Liftoff to Baro patch for the past couple of days. I uses 180 for my TPS Liftoff Max Load. I noticed that when the patch is enabled, during light load, highway cruising the AFR goes lean at times and the car felt pulled back. When the patch is disabled, all seems well again.
Are you experiencing this as well?
RS200Z is offline  
Reply Like
Old May 21, 2014, 08:42 PM
  #63  
EvoM Guru
Thread Starter
iTrader: (6)
 
tephra's Avatar
 
Join Date: Feb 2007
Location: Melbourne, Australia
Posts: 9,486
Received 66 Likes on 42 Posts
can you send me the 2 ROM's? I havn't had any problems with my setup...
tephra is offline  
Reply Like
Old May 22, 2014, 08:08 PM
  #64  
Evolving Member
 
RS200Z's Avatar
 
Join Date: Jan 2009
Location: Singapore
Posts: 150
Received 0 Likes on 0 Posts
Originally Posted by tephra
can you send me the 2 ROM's? I havn't had any problems with my setup...
PM sent!
RS200Z is offline  
Reply Like
Old Jun 3, 2014, 07:37 AM
  #65  
Newbie
 
xFonts's Avatar
 
Join Date: Aug 2013
Location: Plymouth, MN
Posts: 17
Likes: 0
Received 0 Likes on 0 Posts
Would the 3xMAP current readout patch be better with get scaling right or would it be too touchy?



Also for the TPS LiftOff patch have weird effects if you put anything above 0.4% in the Load Multplier End table?
xFonts is offline  
Reply Like
Old Jul 23, 2014, 01:52 AM
  #66  
Evolving Member
 
BerserkerX's Avatar
 
Join Date: Nov 2006
Location: Utah
Posts: 271
Likes: 0
Received 0 Likes on 0 Posts
Have these been defined for 59590004 or not yet?
BerserkerX is offline  
Reply Like
Old Jul 23, 2014, 04:12 AM
  #67  
Newbie
 
Drkramm's Avatar
 
Join Date: Oct 2012
Location: pa
Posts: 64
Likes: 0
Received 0 Likes on 0 Posts
Anyone got 56890009 ?
Drkramm is offline  
Reply Like
Old Feb 8, 2015, 11:29 AM
  #68  
Evolved Member
iTrader: (7)
 
chetrickerman's Avatar
 
Join Date: Dec 2008
Location: Colorado Springs
Posts: 575
Received 1 Like on 1 Post
Originally Posted by itzwolf
Had a little time today so gave the 3xMAP tables use actual MAP, not averaged digging a go. I haven't tried any of these so as always proceed with caution and hopefully tephra wouldn't mind confirming.

Enjoy!

55570006:

Code:
<table name="3xMAP tables use actual MAP, not averaged 0xC79E -> 0xC6F2" category="Misc" address="62c84" type="1D" scaling="Hex16"/>
In this one, are you sure its 0xC6F2?

I am getting 0xC6F4
chetrickerman is offline  
Reply Like
Old May 23, 2015, 07:07 AM
  #69  
Evolved Member
iTrader: (7)
 
chetrickerman's Avatar
 
Join Date: Dec 2008
Location: Colorado Springs
Posts: 575
Received 1 Like on 1 Post
Originally Posted by itzwolf
Had a little time today so gave the 3xMAP tables use actual MAP, not averaged digging a go. I haven't tried any of these so as always proceed with caution and hopefully tephra wouldn't mind confirming.

Enjoy!

55570006:

Code:
<table name="3xMAP tables use actual MAP, not averaged 0xC79E -> 0xC6F2" category="Misc" address="62c84" type="1D" scaling="Hex16"/>
In this one, are you sure its 0xC6F2?

I am getting 0xC6F4

Tephra, can you confirm?
chetrickerman is offline  
Reply Like
Old Mar 1, 2019, 01:10 PM
  #70  
Newbie
 
sleandro's Avatar
 
Join Date: May 2017
Location: curitiba, pr, brazil
Posts: 20
Received 1 Like on 1 Post
Yeah, I'm 4 years late...
Can anyone please help me find the tables bellow in my 56950008 with tephramod v3?

ECT Compensation for Load
MAF IAT Compensation for Load
Baro Compensation for Load
Load multiplier when TPS increased by %
Load multiplier end when TPS decreased by % (hysteresis)
Load multiplier when TPS Increasing - MAP High Load Multi
Load multiplier when TPS steady - MAF/MAP Low Load Multi
Load multiplier - TPS steady Decay Rate
Load Increase/Decrease threshold" category="Load" address="53ca6" type="1D" scaling="Loadify_x50"/>
Load Increase/Decrease divider (ie 1 is biggest)" category="Load" address="530e8" type="1D" scaling="uint16"/>
Load Increase/Decrease multiplier (ie 1 is smallest) #1" category="Load" address="530e4" type="1D" scaling="uint16"/>
Load Increase/Decrease multiplier (ie 1 is smallest) #2" category="Load" address="530e6" type="1D" scaling="uint16"/>
Load RampUP Rate
Load RampDOWN Rate
Load Ramp Rate #1 (Load > 75)
Load Ramp Rate #2
Load Ramp Rate #3
Load Ramp Rate #4

TPS Liftoff Baro to Load patch #1
TPS Liftoff Baro to Load patch #2
TPS Liftoff Max Load patch

3xMAP tables use actual MAP, not averaged
sleandro is offline  
Reply Like
The following users liked this post:
EvO9 PiPER (Nov 16, 2019)
Old Mar 31, 2024, 01:17 PM
  #71  
Newbie
 
dokalanyi's Avatar
 
Join Date: Nov 2019
Location: Kampala
Posts: 15
Likes: 0
Received 0 Likes on 0 Posts
A decade late, but well
Does anyone have these maps for 56920008?
dokalanyi is offline  
Reply Like
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
Omni 4bar writeup
tephra
Evo X Engine Management / Tuning Forums
69
Dec 17, 2022 04:59 AM
Requested Torque/Throttle Ramp Rate Tables
tephra
ECU Flash
59
Aug 1, 2018 01:02 AM
psi based boost control
tephra
Evo X Engine Management / Tuning Forums
151
Jun 18, 2017 03:22 PM
New Maps for Evo 7 and 9
Mattjin
ECU Flash
327
Oct 11, 2009 03:11 AM
Found - Short Term Fuel Trim maps
Mattjin
ECU Flash
35
May 9, 2009 08:40 PM
Back to Subforum
ECU Flash
View Next Unread
EvoX Tephra v3 Some tables not available


Thread Tools
Search this Thread
Search this Thread:

Advanced Search

Advanced Search
Quick Reply: A bunch of load calculation related maps


Reply Closed Thread Share

All times are GMT -7. The time now is 09:47 AM.