New build Tephra V7, SD, No Start/Spark - EvolutionM - Mitsubishi Lancer and Lancer Evolution Community



New build Tephra V7, SD, No Start/Spark

Reply
 
 
 
Thread Tools Search this Thread
Old Sep 17, 2017, 04:08 AM   #1
Evolved Member
Thread Starter
iTrader: (12)
 
Evo8Emperor's Avatar
 
Join Date: Oct 2007
Location: Rhode Island
Posts: 1,271
Thanks: 0
Thanked 0 Times in 0 Posts

Drives: 03 Evo 8, 01 Honda 929RR

New build Tephra V7, SD, No Start/Spark

Ok so i tried posting in the tephra v7 thread but havent had any luck with a reply.

I have a thread up HERE in the Engine/Turbo section trying to diagnosis a no start.

So if you take a look in that thread we have covered a lot of the bases.

I really think its my work in the ROM that might be holding us back but I don't have anyone around to back me up other than the community here.

I believe i did most of all the work if someone can just take a look over my ROM and make sure its set up right.

Again have to run Speed Density. Have GM IAT sensor wired in to MAF and Omni 4 Bar MAP Sensor.
Attached Files
File Type: bin New SD Rom.bin (256.0 KB, 0 views)

Last edited by Evo8Emperor; Sep 17, 2017 at 07:12 AM.
Offline
 
Reply With Quote
Old Sep 17, 2017, 07:11 AM   #2
Evolved Member
Thread Starter
iTrader: (12)
 
Evo8Emperor's Avatar
 
Join Date: Oct 2007
Location: Rhode Island
Posts: 1,271
Thanks: 0
Thanked 0 Times in 0 Posts

Drives: 03 Evo 8, 01 Honda 929RR

Ok so been going through everything and I re set up ecu to run GM IAT sensor on mat input and the 4 bar omni map sensor scaled right and scaling changed in ecuflash.

updated new rom.
Offline
 
Reply With Quote
Old Sep 17, 2017, 07:24 AM   #3
Evolved Member
Thread Starter
iTrader: (12)
 
Evo8Emperor's Avatar
 
Join Date: Oct 2007
Location: Rhode Island
Posts: 1,271
Thanks: 0
Thanked 0 Times in 0 Posts

Drives: 03 Evo 8, 01 Honda 929RR

Is there also anyway someone could hook me up with a updated DataSettings Folder for Evoscan v2.9 ?

Trying to update the xml but doesn't seem like Im getting the new stuff in Evoscan.

Havent been able to connect to car either.
Offline
 
Reply With Quote
Old Sep 17, 2017, 10:39 AM   #4
Evolved Member
Thread Starter
iTrader: (12)
 
Evo8Emperor's Avatar
 
Join Date: Oct 2007
Location: Rhode Island
Posts: 1,271
Thanks: 0
Thanked 0 Times in 0 Posts

Drives: 03 Evo 8, 01 Honda 929RR

log of my car cranking over. anyone see anything that sticks out ?
Attached Files
File Type: csv EvoScanDataLog_2017.09.17_13.31.10.csv (28.1 KB, 0 views)
File Type: csv EvoScanDataLog_2017.09.17_14.01.14.csv (10.3 KB, 0 views)

Last edited by Evo8Emperor; Sep 17, 2017 at 11:12 AM.
Offline
 
Reply With Quote
Old Sep 17, 2017, 02:40 PM   #5
Evolved Member
 
4b11slayer's Avatar
 
Join Date: Nov 2015
Location: Santa Ana
Posts: 1,520
Thanked 69 Times in 69 Posts

Drives: 2004 rs ct9a

Likely an immobilizer issue.
Either wrong code
Ot wrong year selected.

Use the dtc scan option in evoscan. If its imobbilizer related usually theres a trouble code that sets.
Offline
 
Reply With Quote
Old Sep 17, 2017, 02:45 PM   #6
Evolved Member
Thread Starter
iTrader: (12)
 
Evo8Emperor's Avatar
 
Join Date: Oct 2007
Location: Rhode Island
Posts: 1,271
Thanks: 0
Thanked 0 Times in 0 Posts

Drives: 03 Evo 8, 01 Honda 929RR

yeah i checked dtcs with evoscan about an hr ago. no issues at all. immobilizer is disabled and set for 0004 in the immo section
Offline
 
Reply With Quote
Old Sep 17, 2017, 02:54 PM   #7
Evolved Member
 
4b11slayer's Avatar
 
Join Date: Nov 2015
Location: Santa Ana
Posts: 1,520
Thanked 69 Times in 69 Posts

Drives: 2004 rs ct9a

The car would still start with a bad map sensor or iat sensor. Even if the option was incorrect in the rom.
Offline
 
Reply With Quote
Old Sep 17, 2017, 02:55 PM   #8
Evolved Member
 
4b11slayer's Avatar
 
Join Date: Nov 2015
Location: Santa Ana
Posts: 1,520
Thanked 69 Times in 69 Posts

Drives: 2004 rs ct9a

So you have no spark? How about fuel? Have you used a noid light on the injectors?
Offline
 
Reply With Quote
Old Sep 17, 2017, 03:01 PM   #9
Evolved Member
 
4b11slayer's Avatar
 
Join Date: Nov 2015
Location: Santa Ana
Posts: 1,520
Thanked 69 Times in 69 Posts

Drives: 2004 rs ct9a

Have you checked mechanical timing?
Also your sure the crank sensor wheel is on correct?
Offline
 
Reply With Quote
Old Sep 17, 2017, 03:12 PM   #10
Evolved Member
 
4b11slayer's Avatar
 
Join Date: Nov 2015
Location: Santa Ana
Posts: 1,520
Thanked 69 Times in 69 Posts

Drives: 2004 rs ct9a

K


Offline
 
Reply With Quote
Old Sep 17, 2017, 03:15 PM   #11
Evolved Member
 
4b11slayer's Avatar
 
Join Date: Nov 2015
Location: Santa Ana
Posts: 1,520
Thanked 69 Times in 69 Posts

Drives: 2004 rs ct9a

Step 1. Check pin #1 of ignition coils. Should be white red stripe.
Offline
 
Reply With Quote
Old Sep 17, 2017, 03:35 PM   #12
Evolved Member
Thread Starter
iTrader: (12)
 
Evo8Emperor's Avatar
 
Join Date: Oct 2007
Location: Rhode Island
Posts: 1,271
Thanks: 0
Thanked 0 Times in 0 Posts

Drives: 03 Evo 8, 01 Honda 929RR

Crank plate is on right. indent facing in. new crank sensor.

cam reluctor wheel is in right positon. New cam sensor.

Timing is spot on.

We have 12v power right to the coils and good ground. have continuity to ecu as well.
Offline
 
Reply With Quote
Old Sep 17, 2017, 05:31 PM   #13
Evolved Member
 
4b11slayer's Avatar
 
Join Date: Nov 2015
Location: Santa Ana
Posts: 1,520
Thanked 69 Times in 69 Posts

Drives: 2004 rs ct9a

What pin has voltage?
Offline
 
Reply With Quote
Old Sep 17, 2017, 05:32 PM   #14
Evolved Member
 
4b11slayer's Avatar
 
Join Date: Nov 2015
Location: Santa Ana
Posts: 1,520
Thanked 69 Times in 69 Posts

Drives: 2004 rs ct9a

Pin 1 is 12 volts constant ignition on and pin 3 is ecm voltage signal. Pin 2 is ground.
Offline
 
Reply With Quote
Old Sep 18, 2017, 03:08 AM   #15
Evolved Member
Thread Starter
iTrader: (12)
 
Evo8Emperor's Avatar
 
Join Date: Oct 2007
Location: Rhode Island
Posts: 1,271
Thanks: 0
Thanked 0 Times in 0 Posts

Drives: 03 Evo 8, 01 Honda 929RR

Yeah I had 12v power key on at pin 1

Had good ground at pin 3 and not getting signal from ecu for spark obviously so just tested continuity which is good.
Offline
 
Reply With Quote
 
 
Reply

Related Topics
Thread Thread Starter Forum Replies Last Post
Starting Tephra V7 mod DormantBeast General Engine Management / Tuning Forum 13 Jul 9, 2017 07:38 AM
Confirmed: Evo ROM Can Be Flashed to Lancer ECU senate6268 Lancer Engine Management / Tuning Forums 691 Apr 18, 2017 04:03 PM
94170008 Rom Tephra v7 4b11slayer EcuFlash 1 Oct 26, 2016 01:10 PM
Tephra please help evo 8 Zunk87 EcuFlash 5 Sep 1, 2016 03:22 PM
6mt rom ok for 5mt A1hunter EcuFlash 2 Dec 15, 2015 12:44 PM


Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off



All times are GMT -7. The time now is 01:55 PM.


 
  • Ask a Question
    Get answers from community experts
Question Title:
Description:
Your question will be posted in: