Rear fenders rub after installing 18x9.5 +20 with 245's
#1
Evolving Member
Thread Starter
Join Date: May 2006
Location: San Jose, CA
Posts: 146
Likes: 0
Received 0 Likes
on
0 Posts
Rear fenders rub after installing 18x9.5 +20 with 245's
Last weekend, I installed a set of Work CR Kiwami, size 18x9.5 +20. Since I was using 245/40/18's on them, after reading all the threads re: wheel fitment, I figured there would be no rear fender interference. Well, that was not the case. I was getting a slight rub, especially on the right rear making left turns over bumpy roads. The car is lowered on Eibach springs, and BFG G-Force Comp-2's are the tires I'm using. Comparing specs to the OEM Yokohama's, the BFG's are more square and have a slightly larger diameter, and that's more than likely the reason why I was rubbing while other people stated their cars were fine on 245's. I said "was rubbing" because I ended up getting the rear fenders shaved today during lunch. This way, I can go 265's with the next set of tires.
Just thought I'd post this info, in case anyone is interested.
Just thought I'd post this info, in case anyone is interested.
Last edited by acm_evo; Sep 27, 2012 at 03:32 PM.
#6
Evolving Member
Thread Starter
Join Date: May 2006
Location: San Jose, CA
Posts: 146
Likes: 0
Received 0 Likes
on
0 Posts
Thanks for the input. However, I'm running around - 1.5 all the way around, and inside thread tire wear is bad enough as-is...
#7
Evolving Member
Thread Starter
Join Date: May 2006
Location: San Jose, CA
Posts: 146
Likes: 0
Received 0 Likes
on
0 Posts
Yes, the inside lip was shaved back a couple mm's. Why would i regret it? I did seal the cut edges with factory touch up paint, and here in CA where i live rusting is really not a major issue. I debated whether getting the fenders rolled or shaved, and I guess i chose what i thought, IMHO, was the safest way to solve the rubbing and not screw up the rear fenders' paint and straight edges. I've read countless threads about rolling vs. shaving, and i think there are pros-cons either way you go about it...
Trending Topics
#9
Evolving Member
Thread Starter
Join Date: May 2006
Location: San Jose, CA
Posts: 146
Likes: 0
Received 0 Likes
on
0 Posts
Hi Iowa, good question. Although i don't remember the exact specs, toe is within specs, and pretty close to 0. Prior to replacing tires and getting it realigned, toe was slightly off, and I'm sure that contributed to the right front tire wearing out the inside shoulder. Car was realigned again after the spring installation, and set to as close to 0 toe as possible. Hopefully, this time around front tire wear will be better.
#10
Evolved Member
iTrader: (1)
Well, then the issue with the rubbing in the rear really boils down to the incredible tread-width of the Comp-2s. With the same rear alignment, my R-S3s are no where near the fender lips on a +23 offset, for example. But, of course, a 245/40/18 Comp-2 is almost an inch wider at the tread than the same-size R-S3. Let this be a general warning to everyone that you have to take the tire's specifics into account when using what people have said will fit without rubbing.
#11
Evolved Member
iTrader: (72)
Have you tried to figure out where exactly it's rubbing? I've fitted some big wheels and tires on an X, and have them fitted perfectly without rubbing; only needed to roll the fenders flat. I would advise you to pull a shock off, compress the wheel, and see where it rubs. Then address that issue.
#12
Evolving Member
Thread Starter
Join Date: May 2006
Location: San Jose, CA
Posts: 146
Likes: 0
Received 0 Likes
on
0 Posts
Well, then the issue with the rubbing in the rear really boils down to the incredible tread-width of the Comp-2s. With the same rear alignment, my R-S3s are no where near the fender lips on a +23 offset, for example. But, of course, a 245/40/18 Comp-2 is almost an inch wider at the tread than the same-size R-S3. Let this be a general warning to everyone that you have to take the tire's specifics into account when using what people have said will fit without rubbing.
Have you tried to figure out where exactly it's rubbing? I've fitted some big wheels and tires on an X, and have them fitted perfectly without rubbing; only needed to roll the fenders flat. I would advise you to pull a shock off, compress the wheel, and see where it rubs. Then address that issue.
#13
EvoM Guru
iTrader: (1)
Well, then the issue with the rubbing in the rear really boils down to the incredible tread-width of the Comp-2s. With the same rear alignment, my R-S3s are no where near the fender lips on a +23 offset, for example. But, of course, a 245/40/18 Comp-2 is almost an inch wider at the tread than the same-size R-S3. Let this be a general warning to everyone that you have to take the tire's specifics into account when using what people have said will fit without rubbing.
this kinda sucks, cause i was planning to get these wheels with some 265's in the spring...
#15
Evolving Member
I have the exact same wheels but I'm lowered on swift spec r. I currently still have the OEM tires so there is a slight stretch, but I certainly don't have any rubbing issues.