Who stuffed my rotors?
#1
Newbie
Thread Starter
Join Date: Feb 2016
Location: SA
Posts: 15
Likes: 0
Received 0 Likes
on
0 Posts
Who stuffed my rotors?
Hi there,
My Evo X Final Edition’s stock brake pads were running low. I recently took my own new brake pads to the dealership for servicing and installing the new pads. The dealership outsourced the 'disk machining' job to some workshop (to my knowledge it’s a business for normal cars but not performance car workshop) because the rotor has to be machined first before installing the new pads. The workshop guys said to the dealership staff that 'the metal part of the rotor is too strong to be machined, we have to slow down' (quoting what the staff told me) to make the process work, but eventually, they failed. The rotor (front one) surface is not flat (described as the wave kind of surface by the dealership staff) after they finished, and it's recommended not to be used. Then, they didn't machine the other front one. The two rear ones were machined. The dealership staff suggests me to get new rotors. The quoted genuine part is $3500 for the two front rotors (I asked that the hats are good - it’s a two piece rotor). However, I suspect that the workshop guys didn't recognise that my rotors were genuine 'performance rotors' which is stronger than the normal vehicle, then they might have miss-operated by applying normal rotor machining process, which damaged my rotor. I don't have a way to prove this at the moment, but after consulting with my car club guys, motorsport people and my mechanics, I believe that I have reasonable doubts that this outsourced workshop should be at fault. This results in that I lost two front rotors that should have more than half of its lifetime and I'm worried about the safety of the rear ones.
I got my car in Feb 2016, only daily driving and hill cruise, but not track days. It’s done 33000 km atm.
What at do you think? Is it the workshop who stuffed my rotor?
The images show the damaged rotor. The ‘cuts’ look rough.
My Evo X Final Edition’s stock brake pads were running low. I recently took my own new brake pads to the dealership for servicing and installing the new pads. The dealership outsourced the 'disk machining' job to some workshop (to my knowledge it’s a business for normal cars but not performance car workshop) because the rotor has to be machined first before installing the new pads. The workshop guys said to the dealership staff that 'the metal part of the rotor is too strong to be machined, we have to slow down' (quoting what the staff told me) to make the process work, but eventually, they failed. The rotor (front one) surface is not flat (described as the wave kind of surface by the dealership staff) after they finished, and it's recommended not to be used. Then, they didn't machine the other front one. The two rear ones were machined. The dealership staff suggests me to get new rotors. The quoted genuine part is $3500 for the two front rotors (I asked that the hats are good - it’s a two piece rotor). However, I suspect that the workshop guys didn't recognise that my rotors were genuine 'performance rotors' which is stronger than the normal vehicle, then they might have miss-operated by applying normal rotor machining process, which damaged my rotor. I don't have a way to prove this at the moment, but after consulting with my car club guys, motorsport people and my mechanics, I believe that I have reasonable doubts that this outsourced workshop should be at fault. This results in that I lost two front rotors that should have more than half of its lifetime and I'm worried about the safety of the rear ones.
I got my car in Feb 2016, only daily driving and hill cruise, but not track days. It’s done 33000 km atm.
What at do you think? Is it the workshop who stuffed my rotor?
The images show the damaged rotor. The ‘cuts’ look rough.
Last edited by mrmiller; Jul 14, 2018 at 05:41 AM. Reason: Be accurate
#3
Evolved Member
I would definitely favour filing a lawsuit for this if I were in your shoes, and aiming to settle it by asking the dealership to give me a set of Girodisc rotors. Girodisc rotors are cheaper, lighter, and better. In this way everyone is better off.
#4
EvoM Guru
iTrader: (1)
WAFJ. The rotor is no harder than any other rotor. They tried to make too deep of a cut with the tool moving too quickly. The place that machined those rotors ****ed up and owes you a set of rotors.
#5
Jesus what a ****ing amateur mistake. Looks like they used a dull tool and ran it way too deep. In my exp resurfacing rotors is not really something that is done anymore. you clean up the rotors and then bed the pads in, or you just replace the rotors with the pads. There is no real reason on a street car that you HAVE to resurface a rotor when replacing pads unless you waited way too long and the rotor surface was damaged.
Someone owes you new rotors, If the OEM ones are $3500 then I would try and get them to pay for some girodisk 2 piece rotors. (although this won't likely happen)
Get in touch with the service manager at the dealership and ask him how he wants to make this right. Let him make the first move, then weigh your options. If he is willing to pay for it all, then no need to get all judge judy on the ****.
Someone owes you new rotors, If the OEM ones are $3500 then I would try and get them to pay for some girodisk 2 piece rotors. (although this won't likely happen)
Get in touch with the service manager at the dealership and ask him how he wants to make this right. Let him make the first move, then weigh your options. If he is willing to pay for it all, then no need to get all judge judy on the ****.
Trending Topics
#8
#10
EvoM Guru
iTrader: (1)
I knew what he meant. Not like he was trying to articulate some complex subject matter where spelling might matter..
#12
EvoM Guru
iTrader: (1)
The better question is how does a dealership not have a brake lathe in their shop..
Thread
Thread Starter
Forum
Replies
Last Post
prj.evo
Evo General
10
Nov 19, 2006 05:04 AM