2016 Lancer GTS tuning
Jul 10, 2017, 12:05 PM
#1
Newbie
Thread Starter
2016 Lancer GTS tuning
Hey all!
I am going to start off by saying I am new to tuning Lancers. What I am trying to do is tune my GF's 2016 Lancer GTS.
Its got the 2.4L 4b12 engine. I dont have the tables for it. Tried to open it many times in Ecuflash with no luck and done a lot of searching haha but finally made an account.
So just wondering what files i need to open the stock file in ECUflash?
I have the stock file, I got with the Tatrix cable.
and that gave me a "read_image.srf" file. And I cant do much with that yet...
Whats the next step?
Thanks in advance!
I am going to start off by saying I am new to tuning Lancers. What I am trying to do is tune my GF's 2016 Lancer GTS.
Its got the 2.4L 4b12 engine. I dont have the tables for it. Tried to open it many times in Ecuflash with no luck and done a lot of searching haha but finally made an account.
So just wondering what files i need to open the stock file in ECUflash?
I have the stock file, I got with the Tatrix cable.
and that gave me a "read_image.srf" file. And I cant do much with that yet...
Whats the next step?
Thanks in advance!
Jul 30, 2017, 04:59 AM
#3
Newbie
Hey all!
I am going to start off by saying I am new to tuning Lancers. What I am trying to do is tune my GF's 2016 Lancer GTS.
Its got the 2.4L 4b12 engine. I dont have the tables for it. Tried to open it many times in Ecuflash with no luck and done a lot of searching haha but finally made an account.
So just wondering what files i need to open the stock file in ECUflash?
I have the stock file, I got with the Tatrix cable.
and that gave me a "read_image.srf" file. And I cant do much with that yet...
Whats the next step?
Thanks in advance!
I am going to start off by saying I am new to tuning Lancers. What I am trying to do is tune my GF's 2016 Lancer GTS.
Its got the 2.4L 4b12 engine. I dont have the tables for it. Tried to open it many times in Ecuflash with no luck and done a lot of searching haha but finally made an account.
So just wondering what files i need to open the stock file in ECUflash?
I have the stock file, I got with the Tatrix cable.
and that gave me a "read_image.srf" file. And I cant do much with that yet...
Whats the next step?
Thanks in advance!
Put your firmware here!
The following users liked this post:
jongingerich (Sep 23, 2017)
Sep 23, 2017, 12:46 PM
#5
Newbie
Hey BigWingThings I have a 2013 Lancer VRX (Aus version of GTS) which I have successfully tuned with extremely good results. I had to define the main maps in the ROM myself. If you post your srf file (should be 1024kB in size), I can create a basic definition file to get you started.
Completely stock, tweaking the mivec intake and exhaust cams, ignition timing and AFR maps gives stunning results in both power and economy. Was going to do a few other mods but now I will keep my money in my pocket.
Completely stock, tweaking the mivec intake and exhaust cams, ignition timing and AFR maps gives stunning results in both power and economy. Was going to do a few other mods but now I will keep my money in my pocket.
The following users liked this post:
greder (Sep 24, 2017)
Sep 24, 2017, 04:17 AM
#8
Newbie
Sep 25, 2017, 12:05 PM
#10
Newbie
Hi jajk,
Thanks for the addresses, but I already found them and many others. You do not have the address of the table, the additive of ignition when the air conditioner is turned on?
Thanks for the addresses, but I already found them and many others. You do not have the address of the table, the additive of ignition when the air conditioner is turned on?
Sep 25, 2017, 03:24 PM
#12
Evolving Member
I'm in an 09 gts and would love learning to tune the rom. In my 03, I had a tactrix and I was learning but what are y'all using for the newer lancers to tune? New cables?
