the car is sooooo cleannn. imo i'm digging the rims {thumbup}
|
OMG, those rims are hot.
|
Originally Posted by Adrey
is this fitment for the evo? any pictures with the titanium lip?
http://www.mynismo.com/products/Defa...id=5839&v=more |
hate those wheels
|
Originally Posted by Axiom-Power
It will fit offering maximum lip. Almost 3 inches all around :eek:
http://www.mynismo.com/products/Defa...id=5839&v=more |
Do you have pictures of this supposed 3" with iforged? Because your LE37s definetely did not have 3" of lip, maybe about 1" because LE37 design is face comes out so much even with a deep offset( I used to run 19x10.5 +15 so don't try to bs me here) and I could only see other photos of your car with NT03+M's cheapie wheels. I really would like to see it with a tape measure for reference.
Because, well , I will post up my calculations of your wheel : http://www.paikmanz33.com/images/wheelfitment.JPG ok so you have 84.3mm of wheel to play with, assuming the wheel is COMPLETELY flat which is impossible for your fronts due to brembo caliper, that would be about 3.3" of lip. However, from my experience fitting wheels usually you have to give at least about 1" of backspace clearing on the wheels rear hub, which allows for caliper clearance. This would reduce you to : about 2.3" of lip all the way around. But I really would like to see the setup. |
1 Attachment(s)
Originally Posted by Paikman GTR
Do you have pictures of this supposed 3" with iforged? Because your LE37s definetely did not have 3" of lip, maybe about 1" because LE37 design is face comes out so much even with a deep offset( I used to run 19x10.5 +15 so don't try to bs me here) and I could only see other photos of your car with NT03+M's cheapie wheels. I really would like to see it with a tape measure for reference.
https://www.evolutionm.net/forums/at...id=98221&stc=1 http://streetfaction.com/gallery/fil...Picture203.jpg |
Hmm I was off about a 1/4". Your ruler measurement isn't from where lip is visible, IE where the face stops overlapping. But :beer: looks good, but not 3" of lip lol.
|
He should smack you like a schoolgirl with that wooden ruler! :lol:
|
Originally Posted by Paikman GTR
Hmm I was off about a 1/4". Your ruler measurement isn't from where lip is visible, IE where the face stops overlapping. But :beer: looks good, but not 3" of lip lol.
I was just suprised that Atom-Power's lip is "almost 3" all the way around with a 19x9 +15 offset ... I would expect to be close to 4" if not bigger. |
I will show you a wheel we have in stock called the VOLK TE37 cup to show you why i dont compare lip sizes like that.. Because it is a 15x7 +40 with techincally through your standards about 2.7" of lip all the way around lol. and whatnoise dont be a homo, I invented stylish fitment in the NW area. I just don't like people to claim things that aren't.
And not trying to argue too much either, it is a big lip for 9.5 +30 on an evo. with the lower disk model it WOULD have 4" of lip, but Mackin said it would not clear brembos. |
car is amazing. I think only certain cars could pull of that wheel and thats one of them. probably would look great on an evo as well. staggered mabey?
|
4 Attachment(s)
Originally Posted by Paikman GTR
I will show you a wheel we have in stock called the VOLK TE37 cup to show you why i dont compare lip sizes like that.. Because it is a 15x7 +40 with techincally through your standards about 2.7" of lip all the way around lol. and whatnoise dont be a homo, I invented stylish fitment in the NW area. I just don't like people to claim things that aren't.
And not trying to argue too much either, it is a big lip for 9.5 +30 on an evo. with the lower disk model it WOULD have 4" of lip, but Mackin said it would not clear brembos. |
Screw the lip debate, that Skyline made my tip wet!
I do like the lip on my GT-7's though |
those wheels are sick !!!!! veryyyyy nice . that wheel could only look good on certain colors and it sure does look great on white
|
All times are GMT -7. The time now is 01:52 AM. |
© 2024 MH Sub I, LLC dba Internet Brands