Project Daily "Daisy"
#20
Those guys over at AG AUTO are great bunch of guys and the owner antony is a stand up guy. had some issues with my car that a couple shops around here kept telling me i needed to rebuild my engine because i went with to high of a compression for E85. And i called antony and he knew the issue over the phone, Took the car to him and he and crisspeed got the car fixed in one day and Made 490HP. If you need help let me know always down to help a Mitsubishi owner...
The following users liked this post:
huzzle101 (Jul 7, 2018)
#21
Those guys over at AG AUTO are great bunch of guys and the owner antony is a stand up guy. had some issues with my car that a couple shops around here kept telling me i needed to rebuild my engine because i went with to high of a compression for E85. And i called antony and he knew the issue over the phone, Took the car to him and he and crisspeed got the car fixed in one day and Made 490HP. If you need help let me know always down to help a Mitsubishi owner...
Here are some updated pictures. Finally did my COP system, car does feel a little better and i should have taken pics of my old spark plugs they looked like they were falling apart.
Only driven on it a few times on it but recently i have been noticing my gas moving a bit quicker than when i first got the car a few months ago. Just did a fill up and will track mileage with light pedal driving.
#23
Hey this maybe a stupid question, i am running a MBC and i am looking to install my Omni 4 Bar map sensor. My question is how would setting up ECU based boost control effect the MBC, would it be suggested i setup my EBC which i have but not installed yet. Just haven't read up on setting my EBC yet can i install the Omni 4 bar without worrying my car wo't run the same.
Any answers greatly appreciated, also I will be going Speed Density in the near future.
Any answers greatly appreciated, also I will be going Speed Density in the near future.
#24
EvoM Guru
iTrader: (12)
Hey this maybe a stupid question, i am running a MBC and i am looking to install my Omni 4 Bar map sensor. My question is how would setting up ECU based boost control effect the MBC, would it be suggested i setup my EBC which i have but not installed yet. Just haven't read up on setting my EBC yet can i install the Omni 4 bar without worrying my car wo't run the same.
Any answers greatly appreciated, also I will be going Speed Density in the near future.
Any answers greatly appreciated, also I will be going Speed Density in the near future.
With speed density, you will use the 4 bar MAP sensor and EBCS. No need to install an IAT sensor as temperature is taken from fuel temp. Duty cycle of the EBCS is then adjust adjusted depending on how much boost you desire from the tune.
#25
The problem is, the ECU cannot affect a MBC. You want to have the EBCS hooked up in place of the manual boost controller. If tuning with the manual boost controller, you have to set your boost first, then tune your fuel and timing map to that boost. It makes it difficult when switching maps.
With speed density, you will use the 4 bar MAP sensor and EBCS. No need to install an IAT sensor as temperature is taken from fuel temp. Duty cycle of the EBCS is then adjust adjusted depending on how much boost you desire from the tune.
With speed density, you will use the 4 bar MAP sensor and EBCS. No need to install an IAT sensor as temperature is taken from fuel temp. Duty cycle of the EBCS is then adjust adjusted depending on how much boost you desire from the tune.
#26
Been a bit slow on the build front, just enjoying the car and planning carefully what i want to have done.
Did install this beautiful short shifter and so far its my favourite mod, my shifts are quick and crisp.
Only thing on final install you have to adjust/cut a bit of the center console for it to fit properly.
Got it from Individual Racing Parts, package came from Lithuania so i think that is where they are based out of, currently say they are working on one for the Evo 10.
https://www.irp.lt/individual-racing...speed-gearbox/ its a bit pricey but it is quality stuff, i got it on sale for Black Friday.
More mods coming up about to go green, FP green.
Did install this beautiful short shifter and so far its my favourite mod, my shifts are quick and crisp.
Only thing on final install you have to adjust/cut a bit of the center console for it to fit properly.
Got it from Individual Racing Parts, package came from Lithuania so i think that is where they are based out of, currently say they are working on one for the Evo 10.
https://www.irp.lt/individual-racing...speed-gearbox/ its a bit pricey but it is quality stuff, i got it on sale for Black Friday.
More mods coming up about to go green, FP green.
The following users liked this post:
huzzle101 (Dec 14, 2018)