EvolutionM - Mitsubishi Lancer and Lancer Evolution Community - Search Results



Showing results 1 to 13 of 13
Search took 0.01 seconds.
Search: Posts Made By: merlin.oz
Forum: EcuFlash Aug 8, 2017, 11:37 PM
Replies: 46
Views: 1,713
Posted By merlin.oz
OP, regarding your ISC table values - you will...

OP, regarding your ISC table values - you will never get sensible results with those values.
I suggest you load the three 2D step position tables with stock and expect the best result to be not many...
Forum: EcuFlash Jun 26, 2017, 04:45 PM
Replies: 2
Views: 943
Posted By merlin.oz
You can connect the Defi's linear boost output...

You can connect the Defi's linear boost output signal into the Evo8 4-plug ECU at pin 73 and log it on MUT38.
This will work for the Evo7 and Evo8.
With an Evo8 3-plug ECU, the MAP input is on pin...
Forum: EcuFlash Apr 13, 2017, 06:00 PM
Replies: 7
Views: 752
Posted By merlin.oz
the 22580006 rom is an Evo5 Ralliart rom, so...

the 22580006 rom is an Evo5 Ralliart rom, so there is nothing wrong with flashing that into the car.

Except that the typical flashing xml for that rom is setup for an Evo5 ECU, and the Evo65...
Forum: EcuFlash Mar 13, 2017, 11:13 PM
Replies: 83
Views: 16,766
Posted By merlin.oz
Chris, There is no rpm comp table as you...

Chris,

There is no rpm comp table as you have described.
You will see negative fuel trim as the engine warms once the engine enters closed loop.
This is because you have a warmup fuel enrichment...
Forum: EcuFlash Feb 21, 2017, 07:30 PM
Replies: 83
Views: 16,766
Posted By merlin.oz
Chriss, add these to your xml. The first item...

Chriss, add these to your xml.
The first item is an updated version of what you already have.
The second item sets the gain under cruise and light throttle conditions.

<table name="Closed-Loop...
Forum: EcuFlash Feb 11, 2017, 10:02 PM
Replies: 44
Views: 2,816
Posted By merlin.oz
I tried a set of the 1050SP injectors and gave up...

I tried a set of the 1050SP injectors and gave up on them.

Went back to the FIC1100 and the fueling is perfect again.
Same on an 8 I worked on last year. Strange results.
Forum: EcuFlash Feb 10, 2017, 06:14 PM
Replies: 4
Views: 616
Posted By merlin.oz
96260509 or 96260709 Both are TephraMod,...

96260509 or 96260709

Both are TephraMod, both work very well.
Forum: EcuFlash Feb 10, 2017, 04:48 PM
Replies: 44
Views: 2,816
Posted By merlin.oz
These are HEATSOAK CONTROL parameters for the...

These are HEATSOAK CONTROL parameters for the fuel pump hi-speed mode
and
for the fuel pressure regulator solenoid hi-pressure mode, ie the reg hose is open to atmos

They operate at startup only...
Forum: EcuFlash Dec 18, 2016, 04:31 PM
Replies: 12
Views: 1,030
Posted By merlin.oz
Ryan, 15FE is the water temp to enable LTFT...

Ryan, 15FE is the water temp to enable LTFT learning.
That, and all the other closed-loop 1D parameters are included in my latest xmls.
Something like 54 parameters. Some are legacy though.
Forum: EcuFlash Nov 14, 2016, 12:50 PM
Replies: 3
Views: 666
Posted By merlin.oz
I believe it is a fuel multiplying factor, that...

I believe it is a fuel multiplying factor, that is in play above the set load threshold and below the minimum set rpm.

As to just why we have such a parameter, off hand I cannot think of a reason....
Forum: EcuFlash Oct 25, 2016, 05:04 PM
Replies: 20
Views: 1,448
Posted By merlin.oz
Your fuel trims are going to move because: 1....

Your fuel trims are going to move because:
1. the engine and air temps were lower first time in the day.
2. later in the day AND after driving the whole intake arrangement has heat soaked and the...
Forum: EcuFlash Jan 2, 2015, 02:12 PM
Replies: 83
Views: 16,766
Posted By merlin.oz
Jeff, add this to you definition and then try...

Jeff, add this to you definition and then try lowering the Closed loop Idle Integral Gain value to help reduce the random swing.

for 9653:

<scaling name="I-Gain" units="%" toexpr="x/327.73"...
Forum: EcuFlash Nov 24, 2010, 02:08 AM
Replies: 15
Views: 7,847
Posted By merlin.oz
for an evo8 low = 0000-3800 rpm mid=...

for an evo8
low = 0000-3800 rpm
mid= 3800-4800 rpm
high=4800-7500 tpm

to get an idea if it is real or false knock, just depress the spark map 10 degrees.
if it still knocks badly, its false...
Showing results 1 to 13 of 13

 
Forum Jump

All times are GMT -7. The time now is 06:55 AM.


We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.