EvolutionM - Mitsubishi Lancer and Lancer Evolution Community - Search Results

Notices
 
Search: Posts Made By: Pal215
Showing results 1 to 25 of 96
Search took 0.02 seconds.
Yesterday, 02:51 PM
Replies: 36
Views: 1,226
Posted By Pal215

Ok Gents, Upon doing more research today: ...

Ok Gents,

Upon doing more research today:

Under Head Length of ARP studs is: 76.2mm
Under Head Length of OEM stud is: 40mm
Therefore, ARP extended stud UHL is 36.2mm longer than the oem...
Jun 26, 2018, 10:30 AM
Replies: 34
Views: 791
Posted By Pal215

I would check the connection going to the oem oil...

I would check the connection going to the oem oil pressure sensor/switch. It may not have "clicked" in all the way. Dipstick for sanity, then start to look elsewhere. Hopefully your oil pump is...
Forum: Evo General
Jun 25, 2018, 04:06 PM
Replies: 59
Views: 3,952
Posted By Pal215

^ More surprising than that is there are many...

^ More surprising than that is there are many people driving around in evo's like that. Some evo's are more beat than cars twice their age due to neglectful owners.
May 17, 2018, 02:09 PM
Replies: 32
Views: 877
Posted By Pal215

Check that camshaft and see if it's bent

Check that camshaft and see if it's bent
May 16, 2018, 02:08 PM
Replies: 608
Views: 52,100
Posted By Pal215

Yes, if you pressurize the top of the injectors...

Yes, if you pressurize the top of the injectors with fuel or cleaning solvent, the bottom of the injectors will begin to leak if they are bad. These injectors have a soft polymer valve that can be...
Forum: Evo X General
May 11, 2018, 09:04 AM
Replies: 14
Views: 906
Posted By Pal215

Because of the California Smog Nazi's. You can...

Because of the California Smog Nazi's. You can still get it through places like Ebay and craigslist though. The only thing I have not been able to buy at ALL is Berkebile Oil 2 + 2 B101 Instant Gum...
May 9, 2018, 02:51 PM
Replies: 17
Views: 587
Posted By Pal215

This exactly. OP, If you worked on this...

This exactly.

OP, If you worked on this particular platform for a while and you already had an idea of what size bolts and misc hardware to expect in all places throughout the car, then I'd say...
May 1, 2018, 09:00 AM
Replies: 608
Views: 52,100
Posted By Pal215

There are certain channels that have it, but I...

There are certain channels that have it, but I forget what they're called. You have to order them from your cable provider specifically. Tom and Jerry, The Flintstones, The Jetsons, Scooby Doo,...
Apr 30, 2018, 01:28 PM
Replies: 608
Views: 52,100
Posted By Pal215

Had some time to play with the car during lunch...

Had some time to play with the car during lunch and flashed an older map, started up right away!

I think I know what's going on. When finalizing the tune, Aaron and I were working on startup...
Apr 27, 2018, 11:30 AM
Replies: 608
Views: 52,100
Posted By Pal215

That would piss me off so much haha. If you're...

That would piss me off so much haha. If you're going to build a heavy amp, at least make the weight useful for something :lol:.
Apr 23, 2018, 04:34 PM
Replies: 16
Views: 563
Posted By Pal215

Yeah, i'm thinking the OP's rod bolts failed. ...

Yeah, i'm thinking the OP's rod bolts failed. Rev it high enough and the stock rod bolts will stretch, leading to a spun bearing.
Apr 12, 2018, 02:41 PM
Replies: 15
Views: 796
Posted By Pal215

Because he's conducting an ethnography for his...

Because he's conducting an ethnography for his class( hopefully lol). Most guys are already into cars and thanks to our restricting social norms, females are not introduced to car stuff at a young...
Apr 12, 2018, 12:10 AM
Replies: 608
Views: 52,100
Posted By Pal215

I finished installing the ACT 6 puck sprung...

I finished installing the ACT 6 puck sprung clutch and prolight flywheel tonight. I just put 30 miles on them and so far I love this setup! No noise at all and engagement is actually smooth. Maybe...
Apr 10, 2018, 08:58 AM
Replies: 608
Views: 52,100
Posted By Pal215

Nice! Let me know if you have any questions. I...

Nice! Let me know if you have any questions. I feel that there is a lot to be learned from this thread, especially when it comes to learning from my mistakes ;)
Apr 5, 2018, 03:17 PM
Replies: 5
Views: 486
Posted By Pal215

I ran RE760's on a 240sx I used to have and had...

I ran RE760's on a 240sx I used to have and had no issues with them. They rode quiet and offered plenty of grip for daily driving, wet traction was good too and that says something considering they...
Apr 5, 2018, 11:07 AM
Replies: 20
Views: 4,462
Posted By Pal215

I see you're a fan of de-badging. I did the same...

I see you're a fan of de-badging. I did the same thing with my APR front splitter, looks super nice with the SE front lip. Very clean car!
Apr 4, 2018, 02:23 PM
Replies: 3
Views: 352
Posted By Pal215

I could be wrong, but that looks like the clutch...

I could be wrong, but that looks like the clutch restriction pill used to slow down the movement of fluid to the slave cylinder so that people don't launch their cars too hard and ruin their...
Apr 3, 2018, 03:39 PM
Replies: 42
Views: 1,084
Posted By Pal215

Carillo Pro H is fine and 85.5mm is still a safe...

Carillo Pro H is fine and 85.5mm is still a safe bore. The biggest challenge is staying clean and organized, but I can offer some tips to help with consistency and reliability. Even today, when...
Apr 3, 2018, 12:16 AM
Replies: 42
Views: 1,084
Posted By Pal215

No problem, I just went through the process so...

No problem, I just went through the process so it's still fresh in my head. I'll answer what I can, but letsgetthisdone knows more. :beer:
Apr 2, 2018, 04:44 PM
Replies: 42
Views: 1,084
Posted By Pal215

Just make sure you tell them what to check. ...

Just make sure you tell them what to check. Building your own engine is not bad, it's just time consuming and you have to be very meticulous. If you can get your hands on a decent set of...
Mar 27, 2018, 04:46 PM
Replies: 5
Views: 450
Posted By Pal215

There is no right answer for this, but plenty of...

There is no right answer for this, but plenty of wrong ones. I have had a great experience using OEM fluids in the drive train. That is, Diaqueen SAE90 in rear diff and transfer case and BG...
Mar 24, 2018, 09:33 PM
Replies: 608
Views: 52,100
Posted By Pal215

Headlights are done and they came out brilliant!...

Headlights are done and they came out brilliant! Such a stupid easy process, but it involves wasting most of the can of 2k clear. Once the catalyst is activated, you have to use the can within 48...
Mar 20, 2018, 01:12 PM
Replies: 45
Views: 1,794
Posted By Pal215

Main bearing failure is more rare than rod...

Main bearing failure is more rare than rod bearing failure, but it can happen under a few circumstances.

1. The main bearing oil clearance was not set properly
2. The Crank was bent
3. Loss of...
Mar 16, 2018, 12:20 PM
Replies: 5
Views: 325
Posted By Pal215

I usually leave the exhaust manifold and turbo...

I usually leave the exhaust manifold and turbo off to give me more space for wiggle room, but I drop it in from the top with the hood off the car. The more you can get on the engine before you send...
Mar 9, 2018, 01:14 PM
Replies: 210
Views: 14,545
Posted By Pal215

I can't wait to see the parts rolling in for this...

I can't wait to see the parts rolling in for this build. A better rod ratio among the strokers and the Mivec head. Subscribed for Sean to show us the right way to build a 4g64!
Showing results 1 to 25 of 96
 


 
Forum Jump

Contact Us Archive Advertising Cookie Policy Privacy Statement Terms of Service

We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.