My JDM Evo VIII
Thread Starter
Evolved Member
iTrader: (1)
Joined: Nov 2008
Posts: 748
Likes: 7
From: Cayman Islands
2.3L and Buschur 5 Speed swap complete!! This is just a video of it idling a few hours after first start up. Need to put on my muffler lol
Last edited by EvoIIIAj; Jul 8, 2015 at 07:35 AM.
Car is looking super sharp!! Nice work!! 
__________________
"Let us help you build your JDM dream!"
www.bulletproofautomotive.com
The Real JDM - Interactive (blog)
Email: sales@bulletproofautomotive.com
Direct North American Dealers for Voltex, Mines, Varis, First Molding, HKS Kansai, Cusco, HKS, Advan, Volk, Ings+1, C-West, Work, and so much more...
"Let us help you build your JDM dream!"
www.bulletproofautomotive.com
The Real JDM - Interactive (blog)
Email: sales@bulletproofautomotive.com
Direct North American Dealers for Voltex, Mines, Varis, First Molding, HKS Kansai, Cusco, HKS, Advan, Volk, Ings+1, C-West, Work, and so much more...
Thread Starter
Evolved Member
iTrader: (1)
Joined: Nov 2008
Posts: 748
Likes: 7
From: Cayman Islands
Updated mod list:
2.3L (Wiseco HD Pistons, Manley Turbo Tuff I-Beam Rods, Manley 100mm Steel Crank)
Buschur Racing Stage One 5 Speed (ACT 6 Puck Clutch Kit w/ Streetlite Flywheel)
FP DBB Red w/ 25PSI WGA
GSC S2 Cams w/ Kiggly Beehive Springs & Titanium Retainers
ARP L19 Headstuds
Curt Brown Ported Intake Manifold
Curt Brown Ported Exhaust Manifold
Curt Brown Ported Throttle Body (65mm)
MAP 3” o2 Eliminator Downpipe – 3” Titanium Catback
Speed Density Conversion
TSCompTuned 4” SD Intake
ETS 3.5” Intercooler w/ MAP LICP & STM Short Route UICP
Tial Q Blowoff
FIC 1100cc Injectors
Grimspeed 3 Port + Hallman MBC (Hyrbid Boost Set-Up)
2.3L (Wiseco HD Pistons, Manley Turbo Tuff I-Beam Rods, Manley 100mm Steel Crank)
Buschur Racing Stage One 5 Speed (ACT 6 Puck Clutch Kit w/ Streetlite Flywheel)
FP DBB Red w/ 25PSI WGA
GSC S2 Cams w/ Kiggly Beehive Springs & Titanium Retainers
ARP L19 Headstuds
Curt Brown Ported Intake Manifold
Curt Brown Ported Exhaust Manifold
Curt Brown Ported Throttle Body (65mm)
MAP 3” o2 Eliminator Downpipe – 3” Titanium Catback
Speed Density Conversion
TSCompTuned 4” SD Intake
ETS 3.5” Intercooler w/ MAP LICP & STM Short Route UICP
Tial Q Blowoff
FIC 1100cc Injectors
Grimspeed 3 Port + Hallman MBC (Hyrbid Boost Set-Up)
Thread Starter
Evolved Member
iTrader: (1)
Joined: Nov 2008
Posts: 748
Likes: 7
From: Cayman Islands
Hey guys!
Long time since no update. Well that's because I literally haven't been doing anything with my car other than taking it for a drive every now and then. Our drag track has been closed for a few years but it just unofficially re-opened so the hype is back!
Anyway, I was there on Sunday, here's a quick video I did with my GoPro. When I let off the throttle that's the end of the 1/8 mile. If you look closely you'll see the checkered line at the end close to the tower. 1080p quality available.
Long time since no update. Well that's because I literally haven't been doing anything with my car other than taking it for a drive every now and then. Our drag track has been closed for a few years but it just unofficially re-opened so the hype is back!
Anyway, I was there on Sunday, here's a quick video I did with my GoPro. When I let off the throttle that's the end of the 1/8 mile. If you look closely you'll see the checkered line at the end close to the tower. 1080p quality available.
Thread Starter
Evolved Member
iTrader: (1)
Joined: Nov 2008
Posts: 748
Likes: 7
From: Cayman Islands
Thanks! Sure hope it does. I just need to put in the double pumper and schedule a tune with Tom now. I'll be using 93 octane + Sunoco 104 octane race gas. Not sure how far these 1100cc injectors will take me but we'll see!
