Mark this thread as Unsold
[FS] 4G69 2.4L Ralliart part out OEM & aftermarket - 100mm crank, rods, pistons, AEM, ACT
Feb 21, 2015, 02:23 PM
#1
4G69 2.4L Ralliart part out OEM & aftermarket - 100mm crank, rods, pistons, AEM, ACT
4G69 2.4L Ralliart part out
Building my 2.4L short block with a new rotating assembly and doing a DOHC evo 9 head swap. Engine had approximately 49,000 miles at time of dis-assembly; very minimal rust and has been well taken care of which you can see from the quality of the parts.
The crankshaft looks to be in fantastic shape, all bearings are in great shape. This is a 100mm OEM Mitsubishi crank; the lightest 100mm crank they ever made and has been proven to hold up to 800whp of abuse (video). Truthfully had I have known before-hand it was in such great shape, I'd have kept it and saved some cash. Hopefully someone can make good use of it; if not I might just keep it as a back-up.
----
I have everything except for the block itself - let me know what you need! No prices are set in stone, all prices negotiable. I'm mainly looking to help anyone out with their 4G69 build, and to clear some space in the garage!
---
OEM engine parts:
Aftermarket:
Lots of other misc pieces (brackets, sensors...) for sale -- I have it all
Attachment 327755
Attachment 327665
For sale are also an AWD Outlander 2006 manual transmission and transfer case for anyone who might want to take the plunge at a cheap AWD conversion as I did. This transmission is a direct bolt on to the 4G69 block and will accept any 4G69 clutch & flywheel. I can walk you through the entire requirements of the AWD swap should you want to give it a shot. Other parts are needed that I do not have for sale, but I can also do my best to help get you in touch with salvage yards I know have these for sale.
Building my 2.4L short block with a new rotating assembly and doing a DOHC evo 9 head swap. Engine had approximately 49,000 miles at time of dis-assembly; very minimal rust and has been well taken care of which you can see from the quality of the parts.
The crankshaft looks to be in fantastic shape, all bearings are in great shape. This is a 100mm OEM Mitsubishi crank; the lightest 100mm crank they ever made and has been proven to hold up to 800whp of abuse (video). Truthfully had I have known before-hand it was in such great shape, I'd have kept it and saved some cash. Hopefully someone can make good use of it; if not I might just keep it as a back-up.
----
I have everything except for the block itself - let me know what you need! No prices are set in stone, all prices negotiable. I'm mainly looking to help anyone out with their 4G69 build, and to clear some space in the garage!
---
OEM engine parts:
- SOHC 4G69 complete head -- SOLD
- OEM 4G69 100mm crankshaft -- SOLD
- OEM crank pulley -- SOLD
- OEM connecting rods, pistons and bolts w/ end caps + bolts - $100 USD
- OEM valve cover - $50 USD
- OEM fuel rail + injectors - $40 USD
- OEM head studs + main studs - $35 USD
- OEM intake manifold - $75 USD
- OEM lower timing belt cover - $30 USD
- OEM mivec solenoid - make an offer
- OEM oil pump, complete - make an offer
- OEM oil pan - make an offer
- NPW Japan water pump (less than 2000 miles) - make an offer
- AISIN hydraulic tensioner (less than 2000 miles) - make an offer
- KOYO tensioner bearing, OEM balance shaft tensioner bearing, OEM idler bearing (less than 2000 miles) - make an offer
- OEM 4G69 ECU -- SOLD
- OEM engine wiring harness -- SOLD
- OEM power steering pump w/ bracket -- SOLD
- OEM throttle body -- SOLD
Aftermarket:
- RRM RalliSpec Xbar, front tower brace (only 2000 miles) - REDUCED! - $160 reduced - $130 new price
- RRM camber alignment bolts, front kit - $70 shipped
- Wilwood Big Brake Kit OZ/ES/LS - rotors, calipers, braided lines, pads, mounting h/w -- SOLD
- RRM race headers / down-pipe, includes brand new o2 sensor and CEL eliminator (only 2000 miles) -- SOLD
- Clutchmasters 4G69 light-weight flywheel (only 2000 miles) -- SOLD
- ACT 6-pad sprung HD clutch kit (complete) (only 2000 miles, the disc is BRAND NEW) -- SOLD
- AEM short ram intake, including MAF sensor + K&N Filter(only 2000 miles) -- SOLD
Lots of other misc pieces (brackets, sensors...) for sale -- I have it all
Attachment 327755
Attachment 327665
For sale are also an AWD Outlander 2006 manual transmission and transfer case for anyone who might want to take the plunge at a cheap AWD conversion as I did. This transmission is a direct bolt on to the 4G69 block and will accept any 4G69 clutch & flywheel. I can walk you through the entire requirements of the AWD swap should you want to give it a shot. Other parts are needed that I do not have for sale, but I can also do my best to help get you in touch with salvage yards I know have these for sale.
- 2006 Outlander SE AWD 5spd manul transmission, 60k miles - $500
- 2006 Outlander SE AWD transfer case, 60k miles - $400
Last edited by doncarbone; Sep 28, 2015 at 02:53 PM.
