Finally a 10 second pass....Got traction?
Thread Starter
Evolved Member
iTrader: (23)
Joined: Feb 2007
Posts: 541
Likes: 0
From: San Antonio, Tx
Thanks for the comments everyone. The 60' was a 1.8 on the pass. What really killed me I felt was the 1-2 **** bog...I shifted when I thought the car had caught but apparently was off. Looking at the logs the car fell down to 7psi of boost and had to build back up to 29 from there in 2nd
I like keeping the car @ 29psi on E85...it consistenly traps in the high 130's with traction issues/shifting etc...I'm sure with a clean pass and a cooler night...9's @ 140+ will be no issue at this boost level.
This pass was my 3rd on the D2 coilover setup and Hoosier QTP's...definitely more seat time and adjustments are needed to hit our goals. No burnout was done either prior to the pass, maybe next time I'll try it. The car weighs 2970 with my 220lb self in there. It has full interior with nothing cut out.
Thanks...powerise I have no clue. I haven't dynoed it, I road tune the cars here. Wheels are 5zigen fno1cr's in 15x7 +42offset in matte black.
Thanks again.
Jorge R.
I like keeping the car @ 29psi on E85...it consistenly traps in the high 130's with traction issues/shifting etc...I'm sure with a clean pass and a cooler night...9's @ 140+ will be no issue at this boost level. This pass was my 3rd on the D2 coilover setup and Hoosier QTP's...definitely more seat time and adjustments are needed to hit our goals. No burnout was done either prior to the pass, maybe next time I'll try it. The car weighs 2970 with my 220lb self in there. It has full interior with nothing cut out.
Thanks...powerise I have no clue. I haven't dynoed it, I road tune the cars here. Wheels are 5zigen fno1cr's in 15x7 +42offset in matte black.
Thanks again.
Jorge R.
Nice it def looks like it's making good power.
Is it a fully built motor or just pistons/rods?
Lots more in it w/ that 60ft and 1-2 shift.......it didn't seem like you had any problem w/ power off the line........it sounded like you didn't even use the 2 step to build am i correct in assuming so?
Is it a fully built motor or just pistons/rods?
Lots more in it w/ that 60ft and 1-2 shift.......it didn't seem like you had any problem w/ power off the line........it sounded like you didn't even use the 2 step to build am i correct in assuming so?
Thread Starter
Evolved Member
iTrader: (23)
Joined: Feb 2007
Posts: 541
Likes: 0
From: San Antonio, Tx
A lotta Buschur power. We built the motor using all Buschur spec components. And it's been holding beautifully 
The car weighs 2970 with me in it. Take me out of the equation (220) it's down to 2750. To get it down there with full interior I have Buschur diff mounts/moustache bar, AWD 2piece driveshaft, the 15inch rims with Hoosier QTP's (which weigh about 12lbs less at each corner than stock setup,) 35lbs off for the 3.5exhaust. That's really about it. Oh yea...can't forget the Buschur oil cooler delete mod
Thanks a lot. Yea I tend to take off too quick from the line and not use the 2step completely..still have adjustments to make before I can think if boosting more out of the hole. Motor is fully built 2.0
Jorge R.

The car weighs 2970 with me in it. Take me out of the equation (220) it's down to 2750. To get it down there with full interior I have Buschur diff mounts/moustache bar, AWD 2piece driveshaft, the 15inch rims with Hoosier QTP's (which weigh about 12lbs less at each corner than stock setup,) 35lbs off for the 3.5exhaust. That's really about it. Oh yea...can't forget the Buschur oil cooler delete mod

Nice it def looks like it's making good power.
Is it a fully built motor or just pistons/rods?
Lots more in it w/ that 60ft and 1-2 shift.......it didn't seem like you had any problem w/ power off the line........it sounded like you didn't even use the 2 step to build am i correct in assuming so?
Is it a fully built motor or just pistons/rods?
Lots more in it w/ that 60ft and 1-2 shift.......it didn't seem like you had any problem w/ power off the line........it sounded like you didn't even use the 2 step to build am i correct in assuming so?
Thanks a lot. Yea I tend to take off too quick from the line and not use the 2step completely..still have adjustments to make before I can think if boosting more out of the hole. Motor is fully built 2.0
Jorge R.


