daymean

iTrader: (2)

Hey man
Been around the forum for a while, however i haven't been actively posting.
Would like to firstly say Great Work tephra!

I would also like to find out about the availability of a patched rom id 96260007, its for a JDM EVO 8 MR.

Thanks man

tephra

iTrader: (6)

look in the V5.10 thread - you can upgrade to 96260009

dawnduran

Idea for new patch:
Auto-AFR function
deactivate some individual CEL-codes
JoeBee's patch for coldstart with E85

FastAzzEvo

iTrader: (11)

after copying the xml data from the v5 to my xml file in my ecuflash , i try to save it and get this:

What am I doing wrong?

FastAzzEvo

iTrader: (11)

another issue is the instructions... for my ROM it is

2) Remove your current "Boost Desired Engine Load" #2 and #3, only #1 matters anymore
3) Remove your current "Base Wastegate Duty" #2 and #3, only #1 matters anymore
4) Remove your current Hi/Lo Octane Fuel+Timing #2 and #3, only #1 matters anymore


Now, I don't have 2 or 4 boost desired engine load.... however I do have a
Boost desired engine load #3 (BCLS), but no #2

On Base wastegate duty I only have a Basline WGDC #1 and #3 (BCLS)

and for my hi/lo octane fuel map I have only 1 high and low...

and the ignition I did have a few and edited them as per image

D-VO

iTrader: (1)

Hey Tephra. I'm hoping this is a good place to ask this. I'm using the older version of the NLTS patch for the 96940011. Was there ever a version for the patch with NLTS that included a LOAD setting for this ECU? The code I am currently using is inherent of the 96530006 code that I modified. I think this is correct:

<table name="Tephra Mod Options" category="Mods" address="3fc0c" type="3D" scaling="uint16">
<table name="X" type="Static X Axis" elements="1">
<data>Value</data>
</table>
<table name="Y" type="Static Y Axis" elements="3">
<data>Enable Rev Limit Switching?</data>
<data>Flash CEL on Knock?</data>
<data>Enable NLTS?</data>
</table>
</table>

<table name="KnockSum Required for CEL" category="Mods" address="3fc12" type="1D" scaling="uint16"/>

<table name="Load Required for CEL on Knock" category="Mods" address="3fc14" type="1D" scaling="Load"/>

<table name="CEL on Knock flash time" category="Mods" address="3fc16" type="1D" scaling="ECUTime"/>

<table name="Valet Rev Limit" category="Mods" address="3fc18" type="1D" scaling="RPMLimit"/>

<table name="Valet Rev Limit Time to Activate" category="Mods" address="3fc1a" type="1D" scaling="ECUTime"/>

<table name="NLTS RPM Drop" category="Mods" address="3fc1c" type="1D" scaling="uint16"/>

<table name="NLTS TPS Threshold" category="Mods" address="3fc1e" type="1D" scaling="ThrottlePercentage"/>

<table name="NLTS Speed Threshold" category="Mods" address="3fc20" type="1D" scaling="VehicleSpeed"/>

<table name="NLTS Load Threshold" category="Mods" address="3fc22" type="1D" scaling="Load"/>

It seems to me that no matter where I set the LOAD value to, there's lag on the throttle response while downshifting.

BTW I did load and convert the HEX file provided. Thanks.

tephra

iTrader: (6)

nah you cant just add in new parameters...

u need to run 5.10 96530006...

D-VO

iTrader: (1)

OK. Which thread had fix for the immobilizer while using 96530006? I can't seem to find it now.

logic

iTrader: (2)

http://evoecu.logic.net/wiki/96530006 (current procedure) and http://evoecu.logic.net/wiki/Immobilizer_Disabling (total disabling) are what you're looking for.

D-VO

iTrader: (1)

Awesome thanks! I would have never thought to look for this info in wikipedia.

tephra

iTrader: (6)

nice logic - I keep forgetting to refer ppl to the wiki

Silver05Bullet

iTrader: (51)

i used the patch for 94170015 it works, is there any way we could use this on an evo 9 ?

tephra

iTrader: (6)

firstly look for the v5.10 thread

2nd what romid do u have on the 9? 8859001x??

Danieln

iTrader: (1)

Hi Dave,

Good to write to you....

Tell me please......if I want to add into my stock map 88840017 only your patch for knock cell light is it write to add what i attached here in this post?

Is the same add-on xml files for 88840016 but with some changes that i post it in red.

Still I did`nt recieve hamish cable in order to test your mod and I wanna try this patch now.

Tell me please if this is correct or not....

Is necessary to put 2 options of knock like you have into your mod....or i will leave it like that?

I apreciatte a lot your work.

Take care


<scaling name="Flashtime" units="ms" toexpr="1000*x/102" frexpr="102*x/1000" format="%.0f" min="0" max="100000" inc="1" storagetype="uint16" endian="big"/>
<table name="Flash CEL on Knock?" category="Mods" address="4823c" type="1D" scaling="uint16"/>
<table name="KnockSum Required for CEL" category="Mods" address="4823e" type="1D" scaling="uint16"/>
<table name="Min Load for CEL on Knock" category="Mods" address="480a0" type="1D" scaling="Load"/>
<table name="CEL on Knock flash time" category="Mods" address="48242" type="1D" scaling="Flashtime"/>

tephra

iTrader: (6)

Hi Dan,

Sorry I dont understand what you are asking?