PERRIN Meth Injection Kit Now $729.99 w/Free Shipping
Thread Starter
Former Sponsor
Joined: May 2003
Posts: 138
Likes: 0
PERRIN Meth Injection Kit Now $729.99 w/Free Shipping
BREAKING NEWS!!!
The PERRIN PWI-1 Water/Methanol Injection system is now $729.99 with free shipping included!
The PERRIN Progressive Water Injection kits are instock and ready to ship at the new retail price! Our current retail price $950.00 plus shipping, with our new price reduction to $729.99, plus free shipping, thats more than $220 off the normal price. How can you go wrong.
The low down is below but be sure to check out our website for more information including the history of water injection, downloadable instructions, kit contents and pictures.
http://www.perrinperformance.com/pro...tem?category=3
Packaging
The PWI-1 system has four main components. Pump assembly, Brain Box, Dash display, and Main harness. These pieces are designed as compact as possible to allow for easy integration to your vehicle.
Changes to the PERRIN PWI-1
FLOW SENSOR
Customers that had our previous systems, may have experienced a low flow or fault once and a while, which was cause by a bad flow sensor. A certain number of these sensors got made with the wrong type of plastic which swells in the meth/water. This caused the spiral inner part to stick once and a while.
While Aquamist has been very good about replacing these for customers, it was something that needed to be revamped completely so this never happens again. The new flow sensor has nickel plated brass parts now inplace of some of the plastic parts.
Brain Box
The Brain Box holds the electronics, which control the system. Inside the Brain Box are three trim pots to fine tune the injection start points, pump gain, and nozzles flow rate. Additionally, the box contains a terminal for the dash controller wire harness and a multi-screw connection terminal allowing the main wire harness to be trimmed to any length for a clean install.
DISPLAY
A simple but minor change to the display. Now with a black body, and white writing. This is easier to see, and less obtrusive to have staring at you all the time. Also we listened to what our customers were asking and we made the LED stay on to let the user be aware the system is on and working. Before, it would stay off, and pushing the test button would indicate if the system was turned on.
HARNESS
This is the biggest change to our kit. The original version was setup with most all the wires and harnessed either hardwired to a board, or on one harness. Now the new system has a nice and tidy junction block where everything plugs in. This allows for easier, and cleaner install, along with being able to remove components individually.
Safety Features
The PWI-1 system has safety features far beyond other systems. When an engine is tuned to use Water Injection it will run high horsepower at safer levels. If for any reason water injection is interrupted the cooling ability and detonation suppression it created disappears. Without proper fail safe and warning features can inadvertently cause serious damage to your vehicle.
The PWI-1 incorporates 2 critical safety features. Blocked nozzle detection and water tank level sensor. Competitive systems without these features put your engine in serious jeopardy of a catastrophic failure. The price of the high end PWI-1 system will pay off the first time any of our safety features are activated.
With these new changes/features, the New price of $729.99 makes this system hard to beat!
The PERRIN PWI-1 Water/Methanol Injection system is now $729.99 with free shipping included!
The PERRIN Progressive Water Injection kits are instock and ready to ship at the new retail price! Our current retail price $950.00 plus shipping, with our new price reduction to $729.99, plus free shipping, thats more than $220 off the normal price. How can you go wrong.
The low down is below but be sure to check out our website for more information including the history of water injection, downloadable instructions, kit contents and pictures.
http://www.perrinperformance.com/pro...tem?category=3
Packaging
The PWI-1 system has four main components. Pump assembly, Brain Box, Dash display, and Main harness. These pieces are designed as compact as possible to allow for easy integration to your vehicle.
Changes to the PERRIN PWI-1
FLOW SENSOR
Customers that had our previous systems, may have experienced a low flow or fault once and a while, which was cause by a bad flow sensor. A certain number of these sensors got made with the wrong type of plastic which swells in the meth/water. This caused the spiral inner part to stick once and a while.
While Aquamist has been very good about replacing these for customers, it was something that needed to be revamped completely so this never happens again. The new flow sensor has nickel plated brass parts now inplace of some of the plastic parts.
Brain Box
The Brain Box holds the electronics, which control the system. Inside the Brain Box are three trim pots to fine tune the injection start points, pump gain, and nozzles flow rate. Additionally, the box contains a terminal for the dash controller wire harness and a multi-screw connection terminal allowing the main wire harness to be trimmed to any length for a clean install.
DISPLAY
A simple but minor change to the display. Now with a black body, and white writing. This is easier to see, and less obtrusive to have staring at you all the time. Also we listened to what our customers were asking and we made the LED stay on to let the user be aware the system is on and working. Before, it would stay off, and pushing the test button would indicate if the system was turned on.
HARNESS
This is the biggest change to our kit. The original version was setup with most all the wires and harnessed either hardwired to a board, or on one harness. Now the new system has a nice and tidy junction block where everything plugs in. This allows for easier, and cleaner install, along with being able to remove components individually.
Safety Features
The PWI-1 system has safety features far beyond other systems. When an engine is tuned to use Water Injection it will run high horsepower at safer levels. If for any reason water injection is interrupted the cooling ability and detonation suppression it created disappears. Without proper fail safe and warning features can inadvertently cause serious damage to your vehicle.
The PWI-1 incorporates 2 critical safety features. Blocked nozzle detection and water tank level sensor. Competitive systems without these features put your engine in serious jeopardy of a catastrophic failure. The price of the high end PWI-1 system will pay off the first time any of our safety features are activated.
With these new changes/features, the New price of $729.99 makes this system hard to beat!
