Notices
Lancer General Come on in and discuss the US Lancer.

headers

Thread Tools
 
Search this Thread
 
Old Oct 22, 2008 | 07:30 PM
  #1  
apex33's Avatar
Thread Starter
Newbie
 
Joined: Sep 2008
Posts: 7
Likes: 0
From: ---
headers

question:

i have a 05 oz rally

would this set of headers be okay for my car? if not what should i get??

http://www.roadracemotorsports.com/s...products_id=92
Old Oct 22, 2008 | 08:19 PM
  #2  
soulesswarrior's Avatar
Evolved Member
iTrader: (8)
 
Joined: Aug 2008
Posts: 964
Likes: 0
From: fallbrook
you should buy a set for your oz rally. if im correct the oz rally uses a 4g94 motor. ralliart has a 2.4 4g69 motor man. completly diff car.
Old Oct 22, 2008 | 08:21 PM
  #3  
soulesswarrior's Avatar
Evolved Member
iTrader: (8)
 
Joined: Aug 2008
Posts: 964
Likes: 0
From: fallbrook
http://www.roadracemotorsports.com/s...&products_id=7


there you go
Old Oct 22, 2008 | 08:49 PM
  #4  
apex33's Avatar
Thread Starter
Newbie
 
Joined: Sep 2008
Posts: 7
Likes: 0
From: ---
thanks!

do i need a downpipe or a new cat too?...

im running a stock motor and wondering if i should move to a mivec [if that's even possible] before i start trying to mod anything. i dont know if a engine swap would be worth it. ha any more suggestions as far as upgrades i should get. im kinda lost
Old Oct 22, 2008 | 09:12 PM
  #5  
soulesswarrior's Avatar
Evolved Member
iTrader: (8)
 
Joined: Aug 2008
Posts: 964
Likes: 0
From: fallbrook
people have perfromed swaps but alotta people will just tell you if you want a ralliart or evo dont swap just sell yours and buy a new one. BUT id reccomend saving up for RRMs turbo kit. im not sure how the downpipe is on the oz rally but i know the stock one on ralliart is garbage. If you wanna go NA id suggest the obvious, headers downpipe high flow cat then catback exhause, cold air intake, underdrive pully(great for turbo too) piggyback, port n polish intake mani etc, just like RRM told me, skys the limit with cars, as long as your pockets are deep.
Old Oct 23, 2008 | 04:21 AM
  #6  
apex33's Avatar
Thread Starter
Newbie
 
Joined: Sep 2008
Posts: 7
Likes: 0
From: ---
ha yea that's going to get a little expensive

i guess it'll be worth it though

thanks a lot for the help

[i might need you again though, to make sure i find the right stuff later on if that's okay]

Last edited by apex33; Oct 23, 2008 at 05:02 AM.
Old Oct 23, 2008 | 06:40 PM
  #7  
Cj98's Avatar
Evolved Member
iTrader: (18)
 
Joined: Sep 2006
Posts: 1,213
Likes: 0
From: Topeka, Kansas
There is more information in the other lancer section. More than likely if you want to go fast, Boost or Spray the car
Old Oct 23, 2008 | 07:31 PM
  #8  
soulesswarrior's Avatar
Evolved Member
iTrader: (8)
 
Joined: Aug 2008
Posts: 964
Likes: 0
From: fallbrook
no prob man, just send me a pm

id recomend if you want to go fast go turbo

Last edited by ambystom01; Oct 25, 2008 at 09:54 AM.
Old Oct 24, 2008 | 08:23 PM
  #9  
apex33's Avatar
Thread Starter
Newbie
 
Joined: Sep 2008
Posts: 7
Likes: 0
From: ---
okay

so would these headers

http://www.roadracemotorsports.com/s...&products_id=7

go with this downpipe

http://www.autopartswarehouse.com/de...71147KM02.html

i doubt it, but it's the best i could find
idk where else to look
Old Oct 25, 2008 | 12:09 AM
  #10  
otter's Avatar
EvoM Administrator
20 Year Member
Liked
Loved
Community Favorite
iTrader: (14)
 
Joined: Jun 2004
Posts: 8,624
Likes: 13
From: Seat 8A
Off you go to the proper section.
Old Oct 25, 2008 | 05:14 AM
  #11  
sXericerider's Avatar
Evolving Member
iTrader: (5)
 
Joined: Oct 2006
Posts: 459
Likes: 0
From: Cathedral City,CA
the rrm headers go fine with the stock down pipe. Hope you find what you're looking for with your engine. good luck

Last edited by ambystom01; Oct 25, 2008 at 09:54 AM.
Old Oct 25, 2008 | 05:34 AM
  #12  
eve-slow's Avatar
Evolved Member
iTrader: (68)
 
Joined: Jan 2004
Posts: 3,051
Likes: 1
From: St. Charles, IL
Header. Just one.
Old Oct 25, 2008 | 09:51 AM
  #13  
ambystom01's Avatar
Evolved Member
iTrader: (7)
 
Joined: Sep 2003
Posts: 15,634
Likes: 75
From: Canuckistan
Please search, this has been covered extensively in the past.

Closed.




All times are GMT -7. The time now is 05:03 PM.