View Poll Results: What do you think???
Voters: 20. You may not vote on this poll
Custom CF Dash Completed!!! *Tons of Pics*
Custom CF Dash Completed!!! *Tons of Pics*
Well this is the third thread I have started updating the progress of the custom carbon fiber dash I have been doing and finally after about 30 hours of work, they are all done and ready to be cleared!
Ill let the pics speak for themselves:
Disclaimer: all the pics are shot with a camera phone cause I still dont have my new digicam up and running YET. Sorry in advance.
Close up of the charcoal carbon kevlar material that I used for this project:
Side Dash Panells:
Side Dash Panels Close up:
Full Trunk Floor Mat:
Lower Cubby Hole:
Lower Cubby Hole Close Up:
Lower Cubby Hole Angle:
Lower Cubby Hole Far Unistalled:
Fully Wrapped Edges on all Pieces (Cubby Hole Ex.):
Ash Tray:
Ash Tray Angle:
Ash Tray Installed:
Dimmer Switch Pannel:
Dimmer Switch Pannel Installed:
Glove Box Handle:
Glove Box Handle Installed:
Inner Power Mirror Cover (Before- Right and After- Left):
Inner Power Window Cover Installed:
Center Armrest:
Temp Control Switches:
Temp Control Swtich Close Up:
Center Dash Piece:
Center Dash Piece Angle:
Power Mirror Control Piece:
Front Pillar:
Front Pillar Base Close Up:
Cluster of Pieces:
Radio/Control Dash Piece:
Driver/Passenger Switch Pannels:
Driver's Side Switch Pannel:
Passenger's Side Switch Pannel:
Rear Window Switch Covers (eliminates switches):
Rear Window Switch Covers 2:
My current Projects are:
- cf headliner
- cf rear dash
- cf B and C pillars
I know the pictures are not the greatest quality, so you dont need to let me know the obvious. I will post updates once they are installed, and hopefully using the new digicam (once I get it up and running).
All comments are appreciated, either good or bad. But please Id rather you be constructive and offer suggestions than just bash.
Don't forget to vote on the poll too!
As Always,
~ Nick ~
Ill let the pics speak for themselves:
Disclaimer: all the pics are shot with a camera phone cause I still dont have my new digicam up and running YET. Sorry in advance.
Close up of the charcoal carbon kevlar material that I used for this project:
Side Dash Panells:
Side Dash Panels Close up:
Full Trunk Floor Mat:
Lower Cubby Hole:
Lower Cubby Hole Close Up:
Lower Cubby Hole Angle:
Lower Cubby Hole Far Unistalled:
Fully Wrapped Edges on all Pieces (Cubby Hole Ex.):
Ash Tray:
Ash Tray Angle:
Ash Tray Installed:
Dimmer Switch Pannel:
Dimmer Switch Pannel Installed:
Glove Box Handle:
Glove Box Handle Installed:
Inner Power Mirror Cover (Before- Right and After- Left):
Inner Power Window Cover Installed:
Center Armrest:
Temp Control Switches:
Temp Control Swtich Close Up:
Center Dash Piece:
Center Dash Piece Angle:
Power Mirror Control Piece:
Front Pillar:
Front Pillar Base Close Up:
Cluster of Pieces:
Radio/Control Dash Piece:
Driver/Passenger Switch Pannels:
Driver's Side Switch Pannel:
Passenger's Side Switch Pannel:
Rear Window Switch Covers (eliminates switches):
Rear Window Switch Covers 2:
My current Projects are:
- cf headliner
- cf rear dash
- cf B and C pillars
I know the pictures are not the greatest quality, so you dont need to let me know the obvious. I will post updates once they are installed, and hopefully using the new digicam (once I get it up and running).
All comments are appreciated, either good or bad. But please Id rather you be constructive and offer suggestions than just bash.
Don't forget to vote on the poll too!
As Always,
~ Nick ~
