2006 MR 5spd 430/350 New everything
For Sale2006 Mitsubishi Lancer Evolution
Sep 28, 2022, 06:56 PM | Replies: 25 | Views: 9230
Description:
12/2/22 update:
Taking in car to dealership to get the OEM ROM. Car will then be smogged and then I will be getting another California title.
Price will be going up after.
Well, she's finally for sale. Here is the for build thread:
https://www.evolutionm.net/forums/pr...r-build-8.html
ASAP, I'll be adding videos of all the parts I have laying around. Attached, are a few pictures from the garage, for how. Dry Carbon trunk, APR wing, a ton of maintenance parts, wheels, etc:
Here are the details:
Doing what it does best:
Evo 9MR. 430whp/350wtq on e85 and 350whp/???wtq on 91oct. **Flexfuel**
For reference, the car did a 1'56".xxx at Buttonwillow Raceway Park CW13 and won the SM championship for my local SCCA AutoX group, for 2021.
5spd.
Clean Title. Pink slip in hand. Currently registered in Montana. Car comes with ALL OEM parts needed for registration in all 50 states. Willing to work with buyer to get OEM ROM from local Mitsu dealership to legally pass smog in CA.
Body has right around 140k miles. All else has been replaced. Car is brought out of the garage for HPDE and autox only. Even on HPDE days, I treat the car like a time attack car, so it only does about 3-4 laps per session, and I only do three sessions. I’ve been focused on PBs, not so much on seat time, so that’s why. The car is tuned to beat on day in and day out, which is the reason it doesn’t make eleventy billion whp. You probably won’t win any drag races with it.
The car makes no weird noises.
The front bumper cover and hood has been resprayed due to rock chips. The driver, front fender has also been resprayed due to a spot of peeling paint that I couldn’t stand.
Front bumper has a slot cut in it in case you want to run a tow strap to the crash beam instead of popping the hood to use the strut tower hook.
I’ll add more info as I remember. I’ve owned the car for 7yrs and have done so much, I know I’m forgetting lots.
Exterior:
Strut mount tow hook
OEM window rain guards
CIRO wing
APR wing (not attached)
OEM wing (not attached)
Stubby antenna
Seibon dry carbon trunk (not currently on car)
Rear fenders rolled/pulled to fit 10.5 +38 wheels and 275 tire. Not sure what else will fit, given the SSB rear trailing arms.
Rear wiper removed (included)
New-ish windshield glass
Respray on front bumper cover
Respray on driver front fender (old paint was peeling)
Brand new 18x10 RPF with 275 Nitto NT01 with a few track days left in them.
18x9 XXR something or other. Not sure the model wheel, bronze with brand new Dunlop Direzzas (see pictures)
JDM rear bumper cover with race car scuffs
Engine:
OEM shortblock from Mitsubishi installed in 2017. Approx 1200 miles
GSC S1 cams, springs, and OEM retainers
Kiggly HLA
Blitz FMIC
Injen LICP
Internally and externally coated OEM exhaust manifold
FP HTA 71 turbo with coated hot side.
FP inline feed line filter and steel braided lines (from OFH)
FP silicone intake
Blox air filter
Custom 6.5qt oil pan with internal hinges and oil temp sensor bung.
Titek O2 housing
Unknown 3” downpipe
Unknown resonated 3” test pipe
Unknown 3” exhaust with resonator and Magnaflow straight-through 3” muffler. Works great, sounds awesome, super stealthy.
FIC 1050cc low-z injectors, cleaned/tested by FIC on 6/2021. Car will come with FIC high Z 1200cc fuel injectors, that have been cleaned and tested, a resister box plug, and IAT sensor; full SD conversion kit.
Walbro 255
Front engine roll stop bushing
Evans waterless coolant
AMS (?) crank scraper
Fluidampner crank pulley
Rear balance shaft disconnected
Front stubby balance shaft.
OEM alternator replaced 01/2017
Setrab oil cooler with fan.
Drivetrain:
Shep Evo 8 5spd trans with custom gearing (1-2 was too big of a jump, so mix/matched 8 and 9 gears to close the gap). Approx. 700 miles on build.
Brand new ACT HDSS clutch, monoloc, PP and OEM TOB, still in box.
All new Redline oil/trans fluid/TC fluid/rear diff fluids/oil filter/0-rings/seals awaiting clutch install.
DSS 2-piece carbon fiber drive shaft
TRE rear diff will all bells and whistles approx 500 miles on build. Probably less.
English Racing ACD tune
Braking:
Evo X MR front brake rotors and calipers (adapters included to go back to 8/9 calipers)
Girodisc 2-pice rear rotors
ST43 brake pads all around.
Suspension:
AST 4100 coilovers 9k/11k rates
Perrin PSRS
SSB rear trailing arms
Front stainless tie rod end and ball joint heat shields with gold tape.
Custom sway bar end links with carbon fiber bushings.
Poly bushings everywhere that isn’t spherical.
Robispec 25mm RSB
Vorshlag camber plates
Binary 2” brake cooling ducts (not installed) and tubing (not installed, new in packaging).
Interior/safety:
Sparco Evo US driver seat
Racequip 2” HANS compatible 5-pt harness
Driver side OEM seatbelt.
Evo 8 passenger seat
Schroth asm passenger harness
Passenger side OEM seat belt.
Fire extinguisher
Roll bar to SCCA and NASA specs.
Alcantara wrapped OEM steering wheel
Wideband gauge in place of “Lancer” spot in gauge cluster
E85 gauge in glove box.
All airbags functioning.
3” riser on shifter.
Switch and harness installed for Cool Shirt setup.
Autometer oil temp/oil pressure/boost gauges.
Tactrix 1.3 cable
Wideband sensor serial to USB output cable
Relayed power cord and anchoring strap for cool-shirt system.
Random bits:
To scale splitter template from Professional Awesome to cut your own plywood splitter. Shows cut/mount/diffuser/etc mount points.
A garage full of mostly OEM parts. From coils to sensors. Will come with OEM fuel injectors, down pipe, catalytic converter, and exhaust. See pictures Full interior with VIII rear seats are in storage and will come with the car. I have every nut/bolt/clip/etc for the interior.
Stereo is Pioneer BT/CD/external source deck. I’ve been using an iPod in the glove box. Brand new Focal speakers in the doors.
None of the wiring harnesses in the car have been altered/cut/modified. The car 100% passes smog in CA with the parts put back on and stock tune in place (I do not have a stock tune but can get one).
I’m probably still forgetting some things. I’ll update as I remember.
Last edited by kaj; Dec 2, 2022 at 01:32 PM.
Reply
Thread Starter
Joined: Mar 2006
Posts: 13,634
Likes: 824
From: Fresno, CA
Price seems too low to me given that it's a IX, could be converted to street duty (not fully caged), and it has some very expensive parts on it or included with it. That OEM cat alone is worth like $800 easy. GLWS.
Thread Starter
Joined: Mar 2006
Posts: 13,634
Likes: 824
From: Fresno, CA

Last edited by kaj; Sep 29, 2022 at 01:17 PM.









