Milwaukee - America's Drunkest Evo Owners
Originally Posted by r3z0nate
Call your C.C. company and your work address to the list if you really want to get stuff shipped there...other companys do that also.
Originally Posted by Jeff_Jeske
I think he replaced the motor mounts. Which is great if your mounts are shot.
If mine were shot I would have them replaced under warranty. If you do replace mount make sure you do all of them at the same time. This is a must. Doing one at a time puts additional stress on the worn mounts.
My mounts were like brand spanking new (18k miles) they didn't need replacing.
I find it odd that you don't feel any vibration. I've had poly mounts in almost every car I've had and you definately get vibrations.
If mine were shot I would have them replaced under warranty. If you do replace mount make sure you do all of them at the same time. This is a must. Doing one at a time puts additional stress on the worn mounts.
My mounts were like brand spanking new (18k miles) they didn't need replacing.
I find it odd that you don't feel any vibration. I've had poly mounts in almost every car I've had and you definately get vibrations.
I just replaced the front one with the powerflex mount. In time I will do the rear, but going to wait until I do the clutch again.
Originally Posted by dryad001
yeah, when did you do the grey hair thing?
all stressed out
Last edited by vittorio; Feb 1, 2006 at 06:10 PM.
,but Firenuts doesnt like it that much
Fireball,
Do you happen to have the part numbers for the gaskets that you needed for the hotside install? I need the O2 housing gasket number and anything else I might be missing.
I have the following so far, quantity is first.
4 - MR224441 - 1 x Stud
1 - MR450703 - Donut gasket for the downpipe
1 - MR323654 - Exhaust Manifold gasket (head to manifold)
I know not all are necessary but I just wanted to get each part that I could need for this so that I can order them at Renner sometime next week. I'm shooting to maybe do this next weekend if it's halfway warmer out since my garage is not heated.
I ordered some silver anti-seez that can hold up to 2400F so that should work well.
Do you happen to have the part numbers for the gaskets that you needed for the hotside install? I need the O2 housing gasket number and anything else I might be missing.
I have the following so far, quantity is first.
4 - MR224441 - 1 x Stud
1 - MR450703 - Donut gasket for the downpipe
1 - MR323654 - Exhaust Manifold gasket (head to manifold)
I know not all are necessary but I just wanted to get each part that I could need for this so that I can order them at Renner sometime next week. I'm shooting to maybe do this next weekend if it's halfway warmer out since my garage is not heated.
I ordered some silver anti-seez that can hold up to 2400F so that should work well.
Hey Ryan I kinda need your advice in some stuff. You got pm
Originally Posted by Nez136
I just ordered a laundry list full of gaskets, studs, ect from bryan, i'll look at the list tomorrow to see what i can come up with
Originally Posted by laakness
Fireball,
Do you happen to have the part numbers for the gaskets that you needed for the hotside install? I need the O2 housing gasket number and anything else I might be missing.
I have the following so far, quantity is first.
4 - MR224441 - 1 x Stud
1 - MR450703 - Donut gasket for the downpipe
1 - MR323654 - Exhaust Manifold gasket (head to manifold)
I know not all are necessary but I just wanted to get each part that I could need for this so that I can order them at Renner sometime next week. I'm shooting to maybe do this next weekend if it's halfway warmer out since my garage is not heated.
I ordered some silver anti-seez that can hold up to 2400F so that should work well.
Do you happen to have the part numbers for the gaskets that you needed for the hotside install? I need the O2 housing gasket number and anything else I might be missing.
I have the following so far, quantity is first.
4 - MR224441 - 1 x Stud
1 - MR450703 - Donut gasket for the downpipe
1 - MR323654 - Exhaust Manifold gasket (head to manifold)
I know not all are necessary but I just wanted to get each part that I could need for this so that I can order them at Renner sometime next week. I'm shooting to maybe do this next weekend if it's halfway warmer out since my garage is not heated.
I ordered some silver anti-seez that can hold up to 2400F so that should work well.
The right way to do a hotside is not to pull the entire turbo.
Originally Posted by vittorio
well since everybody is talking about 10.5 hotside for the last 10000000000 days,i just got 0.00000001 hot side for my baby
Originally Posted by Jeff_Jeske
Why do you insist on doing it the hard way? You do not need new gaskets for this project. The EM gasket is multi layer metal and reusable. The O2 gasket is very heavy duty and reusable. Get rid of those studs holding on the turbo and get some grade 8 bolts from your local hardware store for 25 cents.
The right way to do a hotside is not to pull the entire turbo.
The right way to do a hotside is not to pull the entire turbo.
. I'm not going to do it the hard way. The turbo is staying in the car. I plan on using that entire guide as a reference when doing this. This weekend i'm going to take off my manifold heat shield and spray the **** out of the sensors with some PB Blaster. Hopefully it will help in preperation for next weekend or whenever I get to do this.Do you happen to have the right size for the bolts? I've heard of many other people doing this as well.
I'd rather have some peace of mind with the gaskets in the event they get wrecked some how (I know, long shot) but Renner's parts dept. isn't exactly open all day Sat. or Sunday. This is my only car btw.
I do appreciate all the advice since I haven't done this before.