EvolutionM - Mitsubishi Lancer and Lancer Evolution Community
0 2017/04/29 12:54:16
0 2017/04/29 12:54:24
0 2017/04/29 12:54:35
0 2017/04/29 12:54:43
Shaved the circled brackets off
Shaved the circled brackets off
0 2017/04/29 13:06:34
0 2017/04/30 12:03:00
Bag of unused wiring and connectors not including tape or door harnesses
Bag of unused wiring and connectors not including tape or door harnesses
0 2017/05/03 14:19:55
A little over 6lbs
A little over 6lbs
0 2017/05/03 14:20:03
Finally all trimmed down.
Finally all trimmed down.
0 2017/05/03 14:20:12
Just under 4lbs
Just under 4lbs
0 2017/05/03 14:20:20
Door harnesses and misc plastics.
Door harnesses and misc plastics.
0 2017/05/03 14:20:28
0 2017/05/06 11:40:25
Wiring still on the engine side. Pulled red wire through. It goes to the relay panel on the pass side firewall. Going to use the original relay/power/fuse and just run a splice back to the pump from this wire. All the other wiring is pined directly to the ACD ECU.
Wiring still on the engine side. Pulled red wire through. It goes to the relay panel on the pass side firewall. Going to use the original relay/power/fuse and just run a splice back to the pump from this wire. All the other wiring is pined directly to the ACD ECU.
0 2017/05/06 11:40:35
Wiring pulled back through into cabin, ACD pump/line removed from car.
Wiring pulled back through into cabin, ACD pump/line removed from car.
0 2017/05/06 11:40:44
Wiring still on the engine side.
Wiring still on the engine side.
0 2017/05/06 11:40:54
0 2017/05/06 12:20:17
0 2017/05/06 12:20:26
0 2017/05/06 12:20:34
0 2017/05/06 12:20:44
0 2017/05/10 12:53:44
Added piece of flat steel for bolt hole on the left.
Added piece of flat steel for bolt hole on the left.
0 2017/05/16 13:02:18
Made a mess...
Made a mess...
0 2017/05/16 13:02:28
Just mocking it up
Just mocking it up
0 2017/05/16 13:02:37
0 2017/05/16 13:02:46
0 2017/05/16 13:02:56
0 2017/05/16 13:03:04
0 2017/05/26 12:55:53
0 2017/05/27 09:12:40
0 2017/05/31 12:54:42
OE front strut bar.
OE front strut bar.
0 2017/05/31 12:54:51
0 2017/05/31 12:54:59
0 2017/05/31 12:55:08
Slight kink I managed to put in the line...
Slight kink I managed to put in the line...
0 2017/06/04 12:27:02
Made supplemental bracket and pump will now be in a "basket" for additional stability/rigidity.
Made supplemental bracket and pump will now be in a "basket" for additional stability/rigidity.
0 2017/06/04 12:27:10
Ugly welds but its solid. Welded the opposite side edge as well.
Ugly welds but its solid. Welded the opposite side edge as well.
0 2017/06/04 12:27:19
0 2017/06/04 12:27:28
Small kink... -____-
Small kink... -____-
0 2017/06/04 12:29:36
Supplemental bracket. Pump will be in a "cradle" for extra rigidity and stability.
Supplemental bracket. Pump will be in a "cradle" for extra rigidity and stability.
0 2017/06/04 12:29:44
Ugly welds but its solid. Also welded the opposite side edge where it meets the OE bracket. Gotta grind it and clean it all up still.
Ugly welds but its solid. Also welded the opposite side edge where it meets the OE bracket. Gotta grind it and clean it all up still.
0 2017/06/04 12:29:53
0 2017/06/04 12:30:01