EvolutionM - Mitsubishi Lancer and Lancer Evolution Community
0 2017/11/15 16:46:14
Timing set.
Timing set.
0 2017/11/15 16:38:51
0 2017/11/15 16:38:50
0 2017/11/15 16:38:50
Cylinder head, bolted to the car.
Cylinder head, bolted to the car.
0 2017/11/15 16:38:49
New head gasket on. 4th one in less than 2 years?
New head gasket on. 4th one in less than 2 years?
0 2017/11/15 16:38:48
I decided to upgrade to ARP 625+ head studs because I did not like that you can't even touch L19's without wearing gloves. You can reuse these head studs multiple times and be ok..and you can touch them!
I decided to upgrade to ARP 625+ head studs because I did not like that you can't even touch L19's without wearing gloves. You can reuse these head studs multiple times and be ok..and you can touch them!
0 2017/11/15 16:38:48
Water pump, cylinder block bracket, timing tensioner arm
Water pump, cylinder block bracket, timing tensioner arm
0 2017/11/14 11:11:17
Oil pump front cover cleaned and installed.
Oil pump front cover cleaned and installed.
0 2017/11/14 11:11:16
All pistons in their new (old) home. All rings clocked properly
All pistons in their new (old) home. All rings clocked properly
0 2017/11/14 11:11:16
Packing oil pump with vaseline
Packing oil pump with vaseline
0 2017/11/14 11:11:15
My workbench
My workbench
0 2017/11/14 11:11:14
Tapered piston ring compressor
Tapered piston ring compressor
0 2017/11/14 11:11:14
2 in!
2 in!
0 2017/11/14 11:11:13
0 2017/11/09 11:51:37
Wth?
Wth?
0 2017/11/06 22:24:13
Unknown 6th ring.
Unknown 6th ring.
0 2017/11/06 22:24:07
0 2017/11/05 23:18:24
0 2017/11/05 23:18:14
0 2017/11/05 23:18:05
So much left to do....
So much left to do....
0 2017/11/05 18:39:20
Cleaned as far up the intake ports as I could reach.
Cleaned as far up the intake ports as I could reach.
0 2017/11/05 18:39:11
Resurfaced cylinder head. This is after I also cleaned the hell out of the valve heads. They were covered with carbon and burnt oil even after hot tank.
Resurfaced cylinder head. This is after I also cleaned the hell out of the valve heads. They were covered with carbon and burnt oil even after hot tank.
0 2017/11/05 18:39:03
After cleaning the HELL out of the pistons. I killed 12 dremel attachments. Don't allow your engine to burn this much oil or you will be doing the same.
After cleaning the HELL out of the pistons. I killed 12 dremel attachments. Don't allow your engine to burn this much oil or you will be doing the same.
0 2017/11/05 18:38:54
After cleaning Piston
After cleaning Piston
0 2017/11/05 18:38:47
Before cleaning piston
Before cleaning piston
0 2017/11/05 18:38:38
Crank endplay in spec
Crank endplay in spec
0 2017/11/05 18:38:30
Checking micrometer calibration
Checking micrometer calibration
0 2017/11/05 18:38:19
Measuring journals
Measuring journals
0 2017/11/05 18:38:13
Pre-cleaning crank
Pre-cleaning crank
0 2017/11/05 18:38:05
Had to move the damn engine block to my table to get to the last two main bearing bores. I don't have a 7 foot dial bore gauge.
Had to move the damn engine block to my table to get to the last two main bearing bores. I don't have a 7 foot dial bore gauge.
0 2017/11/05 18:37:57
Measuring main bores with bearings in place using dial bore gauge
Measuring main bores with bearings in place using dial bore gauge
0 2017/11/05 18:37:47
Torqued to 60ft lbs in 3 steps to take measurements
Torqued to 60ft lbs in 3 steps to take measurements
0 2017/11/05 18:37:37
Lots of Lube!
Lots of Lube!
0 2017/11/05 18:37:25
Main studs back in
Main studs back in
0 2017/11/05 18:37:14
Main bearings back in after lots of cleaning
Main bearings back in after lots of cleaning
0 2017/11/05 18:37:03
New Hone Crosshatch
New Hone Crosshatch
0 2017/11/05 18:36:53
Oil Squirters back in
Oil Squirters back in
0 2017/11/05 18:36:44
Thanks for looking!
Thanks for looking!
0 2017/11/05 18:36:34
0 2017/10/26 14:28:05