EvolutionM - Mitsubishi Lancer and Lancer Evolution Community
0 2018/08/26 18:32:48
I wrapped the wiring under the fender with a 1/2" piece of convolute and electric tape.
I wrapped the wiring under the fender with a 1/2" piece of convolute and electric tape.
0 2018/08/26 18:32:49
0 2018/08/26 18:36:57
0 2018/08/26 18:36:58
I made a shim from nylon to make the top clamp full fit and constrain the battery side to side as well as hold it down.
I made a shim from nylon to make the top clamp full fit and constrain the battery side to side as well as hold it down.
0 2018/08/26 18:36:58
battery fits in quite nicely and very snug
battery fits in quite nicely and very snug
0 2018/08/26 18:36:58
0 2018/08/27 22:48:25
0 2018/08/27 22:48:26
0 2018/08/27 22:48:27
0 2018/08/27 22:48:27
0 2018/08/27 22:48:27
0 2018/08/27 22:48:28
0 2018/08/27 22:49:07
0 2018/08/27 22:50:20
mounting the evo x fusible link to my bracket
mounting the evo x fusible link to my bracket
0 2018/09/01 06:32:33
All of my wires connected to the fusible link
All of my wires connected to the fusible link
0 2018/09/01 06:33:11
stripping the 1 gauge for receiving the terminal
stripping the 1 gauge for receiving the terminal
0 2018/09/01 06:33:53
it is important to fully seat the wiring in before crimping. I used a hydraulic crimper. This worked out fantastic. Very easy to get amazing results.
it is important to fully seat the wiring in before crimping. I used a hydraulic crimper. This worked out fantastic. Very easy to get amazing results.
0 2018/09/01 06:34:20
0 2018/09/01 06:35:28
Here I used the shrink-wrap that has the sealant inside. It flows out as the shrink-wrap gets smaller to provide a more water-proof seal.
Here I used the shrink-wrap that has the sealant inside. It flows out as the shrink-wrap gets smaller to provide a more water-proof seal.
0 2018/09/01 06:35:44
I had to zip tie the wiring up so it would not interfere with the shifting mechanisms on top of the transmission
I had to zip tie the wiring up so it would not interfere with the shifting mechanisms on top of the transmission
0 2018/09/01 06:36:43
0 2018/09/01 06:37:34
0 2018/09/01 06:37:34
0 2018/09/01 06:37:52
0 2018/09/01 06:38:18
here you can see the start of the vent. I routed it from the battery, towards the drivers side and I went back by the tail light.
here you can see the start of the vent. I routed it from the battery, towards the drivers side and I went back by the tail light.
0 2018/09/01 06:38:45
tucking behind the trim on the shock cover in the back
tucking behind the trim on the shock cover in the back
0 2018/09/01 06:39:46
routed and zip tied, going rearward towards the tail light area
routed and zip tied, going rearward towards the tail light area
0 2018/09/01 06:40:23
here is the hold I used to exit the interior. Underneath this threaded hole is where the carbon can vents. It is inside the floor-pan rail
here is the hold I used to exit the interior. Underneath this threaded hole is where the carbon can vents. It is inside the floor-pan rail
0 2018/09/01 06:41:00
I shoved a piece of tig filler metal through the hole, and used it as a guide to pull the hose out all of the way (I thought this was clever)
I shoved a piece of tig filler metal through the hole, and used it as a guide to pull the hose out all of the way (I thought this was clever)
0 2018/09/01 06:41:51
0 2018/09/01 06:43:56
cutting the trim to fit as best as possible
cutting the trim to fit as best as possible
0 2018/09/01 06:44:17
0 2018/09/01 06:44:50
things are mostly trimmed up
things are mostly trimmed up
0 2018/09/01 06:45:07
0 2018/10/15 02:36:47
0 2018/10/15 02:36:47
0 2018/10/15 02:36:48
0 2018/11/02 01:23:04
0 2018/12/25 11:09:03
0 2018/12/25 11:18:28