EvolutionM - Mitsubishi Lancer and Lancer Evolution Community
0 2019/10/19 11:03:53
0 2019/10/19 11:03:55
I ran into problems getting it to fit with the trim installed, I had to make adjustments
I ran into problems getting it to fit with the trim installed, I had to make adjustments
0 2019/10/19 11:04:29
this was the first design....
this was the first design....
0 2019/10/19 11:04:30
the first design had a flat 'bridge" across the top, this didn't work to well. I had to make the raising part at an angle.
the first design had a flat 'bridge" across the top, this didn't work to well. I had to make the raising part at an angle.
0 2019/10/19 11:05:31
Here you can see the circuitboards made from paper, just testing things out
Here you can see the circuitboards made from paper, just testing things out
0 2019/10/19 11:06:30
0 2019/10/19 11:06:31
0 2019/10/19 11:06:39
Here I am transfering the print to copper so I can etch it with a solution
Here I am transfering the print to copper so I can etch it with a solution
0 2019/10/19 11:10:04
the transfer came out fantastic, this will be a good etch
the transfer came out fantastic, this will be a good etch
0 2019/10/19 11:10:05
I always print a few incase I have problems
I always print a few incase I have problems
0 2019/10/19 11:10:06
0 2019/10/19 11:10:07
the boards after drilling the holes and tinning
the boards after drilling the holes and tinning
0 2019/10/19 11:10:09
boards and brackets
boards and brackets
0 2019/10/19 11:10:10
boards and brackets
boards and brackets
0 2019/10/19 11:10:10
boards and brackets
boards and brackets
0 2019/10/19 11:10:11
the boards after drilling the holes and tinning
the boards after drilling the holes and tinning
0 2019/10/19 11:10:12
Here you can see i was test fitting my "circle" style boards before I tinned them.
Here you can see i was test fitting my "circle" style boards before I tinned them.
0 2019/10/19 11:13:00
Here I am with my drill bits, this was many holes I had to drill
Here I am with my drill bits, this was many holes I had to drill
0 2019/10/19 11:13:01
Just comparing.
Just comparing.
0 2019/10/19 11:13:02
Here you can see the circle boards
Here you can see the circle boards
0 2019/10/19 11:13:03
boards before tinning
boards before tinning
0 2019/10/19 11:13:04
all the boards with tinning complete, ready for component soldering.
all the boards with tinning complete, ready for component soldering.
0 2019/10/19 11:13:05
scuffing the cup and preparing it for paint
scuffing the cup and preparing it for paint
0 2019/10/19 11:20:23
base coat sprayed on
base coat sprayed on
0 2019/10/19 11:20:24
clear coat sprayed on
clear coat sprayed on
0 2019/10/19 11:20:25
0 2019/10/19 11:26:53
0 2019/10/19 11:26:55
0 2019/10/19 11:27:54
testing things just for a sanity check
testing things just for a sanity check
0 2019/10/19 11:27:55
0 2019/10/19 11:27:56
0 2019/10/19 11:27:57
0 2019/10/19 11:27:58
0 2019/10/19 11:27:59
0 2019/10/19 11:28:00
0 2019/10/19 11:28:01
0 2019/10/19 11:29:41
0 2019/10/19 11:29:43
without bezel installed
without bezel installed
0 2019/10/19 11:33:02
with bezel installed
with bezel installed
0 2019/10/19 11:33:03