EvolutionM - Mitsubishi Lancer and Lancer Evolution Community
Rear fascia removed
Rear fascia removed
0 2018/05/03 14:54:06
Crash beam removed
Crash beam removed
0 2018/05/03 14:54:07
rear fascia
rear fascia
0 2018/05/03 14:54:08
Testing the fit of the JDM rear
Testing the fit of the JDM rear
0 2018/05/03 14:54:08
The USDM crash beam really sticks out far.
The USDM crash beam really sticks out far.
0 2018/05/03 14:54:08
The JDM rear fascia does contact the exhaust. It will need to be shortened.
The JDM rear fascia does contact the exhaust. It will need to be shortened.
0 2018/05/03 14:54:08
Testing the fit with the jdm rear fascia and no crash beam
Testing the fit with the jdm rear fascia and no crash beam
0 2018/05/03 14:54:08
0 2018/05/03 15:00:55
0 2018/05/03 15:00:56
0 2018/05/03 15:00:56
needed a 1 inch drill bit to make holes so I could get a socket in there
needed a 1 inch drill bit to make holes so I could get a socket in there
0 2018/05/03 15:00:56
it is really tight on the edge, there is only about 1/8 inch of clearance
it is really tight on the edge, there is only about 1/8 inch of clearance
0 2018/05/03 15:00:57
I need to build some sort of support bracket to take advantage of the factory push-pin location that holds the bottom up? See the plastic hole?
I need to build some sort of support bracket to take advantage of the factory push-pin location that holds the bottom up? See the plastic hole?
0 2018/05/03 15:00:58
Very tight fit back here too not much room
Very tight fit back here too not much room
0 2018/05/03 15:00:58
I need to build some sort of support bracket to take advantage of the factory push-pin location that holds the bottom up? See the plastic hole?
I need to build some sort of support bracket to take advantage of the factory push-pin location that holds the bottom up? See the plastic hole?
0 2018/05/03 15:00:58
I need to build some sort of support bracket to take advantage of the factory push-pin location that holds the bottom up? See the plastic hole?
I need to build some sort of support bracket to take advantage of the factory push-pin location that holds the bottom up? See the plastic hole?
0 2018/05/03 15:00:59
I need to build some sort of support bracket to take advantage of the factory push-pin location that holds the bottom up? See the plastic hole?
I need to build some sort of support bracket to take advantage of the factory push-pin location that holds the bottom up? See the plastic hole?
0 2018/05/03 15:00:59
0 2018/05/03 15:00:59
very tight in he
very tight in he
0 2018/05/03 15:00:59
I need to build some sort of support bracket to take advantage of the factory push-pin location that holds the bottom up? See the plastic hole?
I need to build some sort of support bracket to take advantage of the factory push-pin location that holds the bottom up? See the plastic hole?
0 2018/05/03 15:00:59
add a few small tack-welds and check the fit
add a few small tack-welds and check the fit
0 2018/05/09 15:59:04
0 2018/05/09 15:59:06
clamp everything together
clamp everything together
0 2018/05/09 15:59:06
traced onto the aluminum
traced onto the aluminum
0 2018/05/09 15:59:07
0 2018/05/09 15:59:07
cut with saw
cut with saw
0 2018/05/09 15:59:08
0 2018/05/09 15:59:08
0 2018/05/09 15:59:09
0 2018/05/09 15:59:09
0 2018/05/09 15:59:09
0 2018/05/09 15:59:09
testing to see if it will fit between the attachment point on the fascia and the beam
testing to see if it will fit between the attachment point on the fascia and the beam
0 2018/05/09 15:59:09
0 2018/05/09 15:59:10
making a cardboard cut-out that will be the same shape as the aluminum
making a cardboard cut-out that will be the same shape as the aluminum
0 2018/05/09 15:59:10
0 2018/05/11 01:41:33
0 2018/05/11 01:41:34
0 2018/05/13 13:19:10
0 2018/05/29 08:13:53
0 2018/05/29 08:13:53
0 2018/05/29 08:13:54