EvolutionM - Mitsubishi Lancer and Lancer Evolution Community
0 2026/05/09 15:19:12
0 2026/05/09 19:13:25
0 2026/05/09 19:57:37
0 2026/05/09 19:57:39
0 2026/05/09 19:57:41
0 2026/05/09 19:57:44
0 2026/05/09 19:57:46
0 2026/05/09 19:57:48
0 2026/05/09 19:57:51
0 2026/05/09 19:57:53
0 2026/05/09 19:57:56
0 2026/05/09 19:59:56
0 2026/05/09 19:59:59
0 2026/05/09 20:00:01
0 2026/05/09 20:00:03
0 2026/05/09 20:00:05
0 2026/05/09 20:00:08
0 2026/05/09 20:01:34
0 2026/05/09 20:01:36
0 2026/05/09 20:01:39
0 2026/05/09 20:01:41
this was after i did a temp test fit on wire length so ignore the grey and white hahah
this was after i did a temp test fit on wire length so ignore the grey and white hahah
0 2026/05/09 20:01:44
I was in the far left in this picture and i hade to make sure like 5 different times
I was in the far left in this picture and i hade to make sure like 5 different times
0 2026/05/09 20:01:46
This is the trim covering the plug for the oem O2 plug that goes right under the car
This is the trim covering the plug for the oem O2 plug that goes right under the car
0 2026/05/09 20:01:49
Fold the carpet down mine was pre cut as if someone did this before
Fold the carpet down mine was pre cut as if someone did this before
0 2026/05/09 20:01:52
this is the OEM port the stock O2 bung wire uses i recommend you split the oem plug to use or make your own frame metal will cut my thumb got sliced open pushing that plastic bit out in this pic the aem sensor is already installed you'll notice it will have to go sensor threw the hole and leftover cable tuck away haaha legit like 3 to 4 feet of cable is really needed not the whole thing
this is the OEM port the stock O2 bung wire uses i recommend you split the oem plug to use or make your own frame metal will cut my thumb got sliced open pushing that plastic bit out in this pic the aem sensor is already installed you'll notice it will have to go sensor threw the hole and leftover cable tuck away haaha legit like 3 to 4 feet of cable is really needed not the whole thing
0 2026/05/09 20:01:54
0 2026/05/23 12:50:07
0 2026/05/23 12:59:47
0 2026/05/23 13:00:43
After i deep cleaned it top view / inside i also did more cleaning as some spots needed it and polished it in some ruff spots
After i deep cleaned it top view / inside i also did more cleaning as some spots needed it and polished it in some ruff spots
0 2026/05/30 21:20:01
Bottom view also after i deep cleaned it i also did more cleaning as some spots needed it and polished it in some ruff spots
Bottom view also after i deep cleaned it i also did more cleaning as some spots needed it and polished it in some ruff spots
0 2026/05/30 21:20:05
Now the turbo question First: WHAT THE HECK IS THIS RED CIRCLE SPOT LOL 2nd if you look in the deep clean top view you can tell its got structual support so should i install the turbo return bung in the blue spot or in that designated looking spot where a weld bung sits FLUSHHHHH so?????
Now the turbo question First: WHAT THE HECK IS THIS RED CIRCLE SPOT LOL 2nd if you look in the deep clean top view you can tell its got structual support so should i install the turbo return bung in the blue spot or in that designated looking spot where a weld bung sits FLUSHHHHH so?????
0 2026/05/30 21:20:08
Before i deep cleaned it hahaha top view / inside
Before i deep cleaned it hahaha top view / inside
0 2026/05/30 21:20:10
Bottom view also before i deep cleaned it
Bottom view also before i deep cleaned it
0 2026/05/30 21:20:11
0 2026/05/31 12:09:58
0 2026/05/31 12:10:01
0 2026/05/31 12:10:05
0 2026/05/31 12:10:12
0 2026/05/31 12:10:20
0 2026/05/31 12:10:29