Notices

E-brake loose?

Thread Tools
 
Search this Thread
 
Old Jun 1, 2007 | 07:40 PM
  #1  
Realistic's Avatar
Thread Starter
Evolving Member
iTrader: (3)
 
Joined: Apr 2006
Posts: 316
Likes: 0
From: Fort McMurray
E-brake loose?

I was parked in a driveway, kind of on a sland. maybe.. 30 odd degrees, maybe? just a guess.. and i notice that my car started to slide back.


how do i go about tightening my ebrake?
Reply
Old Jun 1, 2007 | 07:57 PM
  #2  
Cj98's Avatar
Evolved Member
iTrader: (18)
 
Joined: Sep 2006
Posts: 1,213
Likes: 0
From: Topeka, Kansas
The cables might be stretched or the pads are worn down. Mine is probly worse then yours...I need to figure out whats wrong with mine also
Reply
Old Jun 1, 2007 | 09:05 PM
  #3  
ixhavexfaithx's Avatar
Evolving Member
 
Joined: Aug 2006
Posts: 225
Likes: 0
From: Northern New York
you can adjust it right under the center console. if that doesnt work you gotta jackup the *** and take off your rear wheels and there's a whole(i cant remember if there's a plug or not) and theres a screw in there you have to find(yes that means spin the drum) and tighten it. do this on both sides and make sure theyre even. it helps to have a friend sit/look in the car to make sure its even.
Reply
Old Jun 1, 2007 | 10:40 PM
  #4  
Truffle Shuffle's Avatar
Evolving Member
iTrader: (1)
 
Joined: Apr 2006
Posts: 178
Likes: 0
Mine was a little loose about a week ago, open the center console and unscrew the two screws at the bottom, pull the center console up and towards the back seats to unhook the two white clasps that are holding it in place towards the front. Once that console comes up you have full access to the E-brake.
Reply
Old Jun 1, 2007 | 11:01 PM
  #5  
hellview's Avatar
Evolving Member
 
Joined: Sep 2006
Posts: 349
Likes: 0
From: chicago, il
throw it in first when the cars off. if you don't already do that.


just a quick q? in the diy forum there one about removing your ebrake handle or somthing. why/ whats the purpose of that
Reply
Old Jun 1, 2007 | 11:55 PM
  #6  
reTro's Avatar
Evolved Member
iTrader: (9)
 
Joined: Oct 2004
Posts: 1,567
Likes: 1
From: San Diego
Originally Posted by hellview
just a quick q? in the diy forum there one about removing your ebrake handle or somthing. why/ whats the purpose of that
Some people were replacing their handles with the Evo MR carbon ones.
Reply
Old Jun 2, 2007 | 04:53 AM
  #7  
bruce988jl's Avatar
Evolved Member
iTrader: (56)
 
Joined: Jun 2004
Posts: 2,568
Likes: 1
From: Boston, MA
Originally Posted by hellview
throw it in first when the cars off. if you don't already do that.


just a quick q? in the diy forum there one about removing your ebrake handle or somthing. why/ whats the purpose of that

You won't pass inspections if your ebrake doesn't work...
Reply
Old Jun 2, 2007 | 10:43 AM
  #8  
ThyPunko_PR's Avatar
Evolving Member
iTrader: (7)
 
Joined: Oct 2004
Posts: 254
Likes: 0
From: Puerto Rico
Got mine ajusted about two weeks ago for the same reason: but I think they got it a little bit too firm....only 3 clicks for full e-brake lock!
Reply
Old Jun 2, 2007 | 11:08 AM
  #9  
Trowa's Avatar
Newbie
 
Joined: Sep 2005
Posts: 15
Likes: 0
From: Toronto, Ontario
I just got mine done too. takes about 30minutes at a dealer and usually they don't charge.
Reply
Old Jun 3, 2007 | 12:27 PM
  #10  
bruce988jl's Avatar
Evolved Member
iTrader: (56)
 
Joined: Jun 2004
Posts: 2,568
Likes: 1
From: Boston, MA
Originally Posted by Trowa
I just got mine done too. takes about 30minutes at a dealer and usually they don't charge.
Where's your dealer.. they must need customers or are really friendly.. cause my dealer would charge me an arm and a leg for that.. even if i take the centerconsole out for them.. haha
Reply
Old Jun 3, 2007 | 12:59 PM
  #11  
superalf574's Avatar
Evolving Member
 
Joined: Jun 2006
Posts: 381
Likes: 0
From: ventura california
got mine done at the dealer when they were doing service they noticed it when the car was parked on a slant and started to roll slowly , mine takes 3 clicks
Reply
Old Jun 3, 2007 | 01:16 PM
  #12  
evoracingstar's Avatar
Evolved Member
iTrader: (31)
 
Joined: Oct 2005
Posts: 1,525
Likes: 1
From: C.T
yeah just take ur center console off and follow the ebrake cable to ur ebrake and you should be able to adjust it from there!
Reply
Old Jun 3, 2007 | 10:10 PM
  #13  
Trowa's Avatar
Newbie
 
Joined: Sep 2005
Posts: 15
Likes: 0
From: Toronto, Ontario
Originally Posted by bruce988jl
Where's your dealer.. they must need customers or are really friendly.. cause my dealer would charge me an arm and a leg for that.. even if i take the centerconsole out for them.. haha
Well, I'm in Canada. and I went to my dealer. "My parking brake is messed, I have to pull it so high, come and I'll show you" so I showed them, and it was damn high. I told them I wanted it covered under warranty. and they did it.
Reply
Related Topics
Thread
Thread Starter
Forum
Replies
Last Post
CaptainCrunch
Evo X General
8
Jun 23, 2016 08:16 PM
GGP Wolf
Mitsubishi TC-SST Discussion
21
Feb 14, 2011 04:44 PM
oftheheavens
Evo X General
3
Oct 15, 2010 09:21 PM
houckeah
EvoM New Member / FAQs / EvoM Rules
7
Dec 25, 2008 01:39 PM
misfit8
Evo How Tos / Installations
3
Jul 7, 2008 03:46 PM




All times are GMT -7. The time now is 03:56 AM.