Evo anti-lag ECU disassembly
#91
Sure, I done another evo7 rom last night (98640014) so hope its similar.
also I am using ecuflash 1.29 so maybe my XML def's arent 100% compatible if your using a later version.....could be the cause of the xxxxx
#93
Okay the ralliart E7 rom has the same locations as the normal E7 rom.
Attached are the XML for
JDM7 : 98640014
Ralliart JDM7 : 90550001
JDM8 : 93660005
8MR : 96260007
All of the above XML's show the air injection table zero'd out on my ecuflash.
If you are manually copying these tables over to your existing XML then If the air injection table doesnt show zero's then you either have a different ROM ID or you forgot to copy the scaling across also. at the top of the XML there are 2 scales (rmpsecbyte and timesecbyte...something like that); make sure you copy these across to your XML as well.
and remember for full benefit you have to retard the ignition timming in the 'back off' areas of your ignition maps (say <30 load and >4000rpm)
Attached are the XML for
JDM7 : 98640014
Ralliart JDM7 : 90550001
JDM8 : 93660005
8MR : 96260007
All of the above XML's show the air injection table zero'd out on my ecuflash.
If you are manually copying these tables over to your existing XML then If the air injection table doesnt show zero's then you either have a different ROM ID or you forgot to copy the scaling across also. at the top of the XML there are 2 scales (rmpsecbyte and timesecbyte...something like that); make sure you copy these across to your XML as well.
and remember for full benefit you have to retard the ignition timming in the 'back off' areas of your ignition maps (say <30 load and >4000rpm)
Last edited by nod911; Mar 12, 2008 at 06:18 PM.
#94
But when I copy the table into my def (as I have V5 patch) the 0.0's go back to xxx's
#95
#99
#100
Yes I missed these 2 scales out, as you added them at the top on the 2 def's I opened first, and so when I found the ALS tables at the bottom, I missed those lines out
<scaling name="RPMstatbyte" units="units" toexpr="x*31.25" frexpr="x/31.25" format="%.0f" min="0" max="11000" inc="1" storagetype="uint8" endian="big"/>
<scaling name="Timesecbyte" units="s" toexpr="x/10" frexpr="x*10" format="%.1f" min="0" max="25.5" inc="1" storagetype="uint8" endian="big"/>
So it was all your fault really
J/K
<scaling name="RPMstatbyte" units="units" toexpr="x*31.25" frexpr="x/31.25" format="%.0f" min="0" max="11000" inc="1" storagetype="uint8" endian="big"/>
<scaling name="Timesecbyte" units="s" toexpr="x/10" frexpr="x*10" format="%.1f" min="0" max="25.5" inc="1" storagetype="uint8" endian="big"/>
So it was all your fault really
J/K
#101
I sorta guessed this because a friend had a similar problem.
So we'll just agree its ecuflash's fault
#102
So a question to everyone curious about this...
the JDM models have twin boost solinoids. I have not heard of a really good reason for this, but this piece of infomation seems to make it clear as to why there are twin solinoids.
could one of these boost solinoids be used to control the air injection?
the JDM models have twin boost solinoids. I have not heard of a really good reason for this, but this piece of infomation seems to make it clear as to why there are twin solinoids.
could one of these boost solinoids be used to control the air injection?
#103
mais pas encore fait les essaie
je vous tiendrait au courant si ca marche ou pas
#104