spoolinspyder

iTrader: (1)

I need a little assistance here guys... After about 4 hours of battling this issue out, i turn to you guys for some help. I have windows 2000 on my dell and everything from the software to the drivers get installed correctly according to the prompts but when i try to read my stock rom i get:

[03:49:46.724] Version 1.28.716
[03:49:46.774] 8 memory models read.
[03:49:47.945] 71 ROM metadata models read.
[03:49:47.945] checksum module "subarudbw" loaded.
[03:49:47.995] flashing tool "wrx02" loaded.
[03:49:47.995] flashing tool "wrx04" loaded.
[03:49:47.995] flashing tool "sti04" loaded.
[03:49:47.995] flashing tool "sti05" loaded.
[03:49:48.005] flashing tool "mitsukernel" loaded.
[03:49:48.005] flashing tool "mitsukernelocp" loaded.
[03:49:48.005] flashing tool "mitsubootloader" loaded.
[03:49:57.569] sending init sequence 1 (0001)
[03:50:00.824] sending init sequence 1 (0003)
[03:50:14.063] sending init sequence 1 (0003)
[03:50:25.279] sending init sequence 1 (0003)
[03:50:28.383] sending init sequence 1 (FFFF)
[03:50:31.648] sending init sequence 1 (0001)
[03:50:32.680] got 0x05 response
[03:50:32.680] sending init sequence 2
[03:50:32.690] got 0x1B response
[03:50:32.700] sending init sequence 3
[03:50:32.770] error sending init sequence 3
[03:51:29.201] sending init sequence 1 (0001)
[03:51:30.222] got 0x05 response
[03:51:30.222] sending init sequence 2
[03:51:30.232] got 0x1B response
[03:51:30.242] sending init sequence 3
[03:51:30.653] entering bootloader
[03:51:30.673] sending kernel size (3392)
[03:51:30.703] sending kernel load address (0xFFFF8800)
[03:51:30.753] uploading kernel
[03:51:31.054] error transmitting kernel
[03:51:43.311] sending init sequence 1 (0001)
[03:51:53.145] sending init sequence 1 (0001)
[03:52:03.410] sending init sequence 1 (0001)
[03:52:11.201] sending init sequence 1 (0001)
[03:52:19.133] sending init sequence 1 (0001)

Being frustrated and all, i borrowed my sisters new Sony VAIO with Windows XP and installed everything on her laptop. Without hesitation BAM it synced up and it was all good. Only problem is that its not my laptop and i cant access it anytime i want. I had everything from file paths to com ports in my laptop set correctly and still NO GO on Windows 2000. Are there any differences between the 2 OS that is screwing up the install?

jcsbanks

I don't know your problem, but I'm reading/logging and flashing with my W2K laptop.

M3this

iTrader: (19)

Try removing and re installing the ECU Flash software.

gsrboi80

iTrader: (38)

I runn 2k for both logging and flashing as well. Works fine. ^^ +1

spoolinspyder

iTrader: (1)

i have tried both removing and re-installing through the device manager and it still wont seem to work. That is what bugs me most is that i know it should work for the windows 2k pro but for some odd reason its not communicationg properly. I tried connecting to the logging software but that didnt work either. Maybe i should try removing all the files including logging software and try re-installing everything again.

spoolinspyder

iTrader: (1)

still no luck guys.... is there a specific folder or designated area to install the files?

MalibuJack

iTrader: (5)

Its possible its your USB port, I haven't tested it on the older laptops, but every platform I tried works fine.. its possible you have a USB1.0 or 1.1 port..

spoolinspyder

iTrader: (1)

Everything installs correctly through the wizard that pops up for both programs and im hoping everything got installed in the right places meaning correct file path names or what so.

spoolinspyder

iTrader: (1)

i finally got it........ i had to re-install the programs under the C drive into the drivers folders. It was installing into the program files the whole time which i thought was correct but i guess i was wrong. Its all good now!

Spec'd

iTrader: (16)

Good job figuring that out.
That's good to know if I run into problems with my old
windows 2000 powered Fujitsui laptop with a Pentium 133.



.

MalibuJack

iTrader: (5)

Yeah I have the drivers "broken out" into a seperate location just in case i have a problem in the future.

spoolinspyder

iTrader: (1)

damnnnnn................ its happening again. The same thing that was happening in the program file is happeing in my drivers program now. I tried removing and re-installing again there, but no luck. What do you guys think is happening

Spec'd

iTrader: (16)

Have you tried going to :

Control Panel > System > Hardware > Device Manager > Universal Serial Bus Controllers > ...

Do you see OpenPort 1.3 Mitsubishi ?



.

spoolinspyder

iTrader: (1)

yea i tried that, it was there and operating properly. I cant seem to figure this out

Spec'd

iTrader: (16)

If you open ECU+ locally on your own laptop and open the EVO8JM9693 example
file does it work normally ?



.