Disabling EGR and fuel pressure solenoids
#110
this thread has a ton of great info in it. Thanks everyone.
1 question: I shut off the FCA, FEA and FAA bits that were mentioned and I flashed it into the car. No CELs or anything. But I didn't disconnect anything (EGR,EVAP,FPR). I just wanted to make sure the ecu stuff worked.
When I started the car up, cold engine, it idled like it had a carb and big cams around 1000 or below haha. Once it got up to temp it idled fine. I'm assuming this is because I shut everything off and still had it all hooked up.
anyone else have this?
1 question: I shut off the FCA, FEA and FAA bits that were mentioned and I flashed it into the car. No CELs or anything. But I didn't disconnect anything (EGR,EVAP,FPR). I just wanted to make sure the ecu stuff worked.
When I started the car up, cold engine, it idled like it had a carb and big cams around 1000 or below haha. Once it got up to temp it idled fine. I'm assuming this is because I shut everything off and still had it all hooked up.
anyone else have this?
#112
thanks for the help Evoryder, is the idle on cold start up the tables found here?
https://www.evolutionm.net/forums/ec...ent-table.html
sorry for the noob questions, just trying to learn everything I can.
https://www.evolutionm.net/forums/ec...ent-table.html
sorry for the noob questions, just trying to learn everything I can.
#114
EvoM Guru
iTrader: (50)
ok, after some more disassem of the EGR routines, I have found that Periphery 0 (FAA) bit11 does not actually shut off the EGR system until the coolant temp passes ~68C. Its ok to use if you plan on ripping out all the EGR stuff. However, it turns out that there is a byte length value that completely disables the EGR system and is a better choice to use.
For USDM Evo 8 94170008-15 and EDM Evo 8 96530006 use:
<table name="EGR System Enable/Disable" category="Emissions EGR" address="103D" type="1D" level="2" scaling="uint8"/>
For USDM Evo 8 96420007-11, 96940011, and USDM Evo 9 88590013-15 use:
<table name="EGR System Enable/Disable" category="Emissions EGR" address="1041" type="1D" level="2" scaling="uint8"/>
A value of "0" disables the EGR system and sets the EGR duty to 0% all the time. "1" enables the EGR system.
Oct 4, 2009 - Fixed to show that the EDM Evo 8 96530006 address is 103D instead of 1041.
For USDM Evo 8 94170008-15 and EDM Evo 8 96530006 use:
<table name="EGR System Enable/Disable" category="Emissions EGR" address="103D" type="1D" level="2" scaling="uint8"/>
For USDM Evo 8 96420007-11, 96940011, and USDM Evo 9 88590013-15 use:
<table name="EGR System Enable/Disable" category="Emissions EGR" address="1041" type="1D" level="2" scaling="uint8"/>
A value of "0" disables the EGR system and sets the EGR duty to 0% all the time. "1" enables the EGR system.
Oct 4, 2009 - Fixed to show that the EDM Evo 8 96530006 address is 103D instead of 1041.
Last edited by mrfred; Oct 4, 2009 at 08:50 AM.