Problem with Ecuflash
#1
Newbie
Thread Starter
Join Date: May 2009
Location: Cincinnati Ohio
Posts: 3
Likes: 0
Received 0 Likes
on
0 Posts
Problem with Ecuflash
I just received my Openport 2.0 cable the other day and now I have spent 2 days trying to flash a 06 Evo 9. I am using Ecuflash version 1.41 and Evoscan version 2.6 beta. I can get the evoscan logger to work but ecuflash won't do anything with the 2.0 cable but I borrowed a 1.3 cable and I can get it to start to read but then it says there is a checksum error and to check the log file. The log file says: chkDisplayTorque_CheckedChanged, Data series with name "Torque" was not found in the series collection.
It also says the same thing about power. I have reinstalled the program a few times and reinstalled the drivders a few times and still nothing. I swapped ecus from another car and still nothing. The 1.3 cable worked on my buddies Evo 8 using evoscan but still wouldn't work with ecuflash. I don't know what to do. I need to get this car running. I tried using the ecuunlocker program and still nothing.
Thanks,
It also says the same thing about power. I have reinstalled the program a few times and reinstalled the drivders a few times and still nothing. I swapped ecus from another car and still nothing. The 1.3 cable worked on my buddies Evo 8 using evoscan but still wouldn't work with ecuflash. I don't know what to do. I need to get this car running. I tried using the ecuunlocker program and still nothing.
Thanks,
#3
Evolved Member
iTrader: (22)
Join Date: Nov 2003
Location: Northern KY near Cincy
Posts: 2,408
Likes: 0
Received 6 Likes
on
6 Posts
I found this.....try it...
"
there're xml definitions for the ecuflash supported cars reside in a directory, usually at:
c:\program files\openecu\ecuflash\rommetadata
Run ecuflash, open File\Options, select Directories\Metadata Directory and set it to the full path to the metadata directory mentioned above.
This will help EcuFlash correctly finding its metadata directory. Usually only "metadata" set in that box and it works because of the executable program relative path is correct but it may not in some cases.
"
"
there're xml definitions for the ecuflash supported cars reside in a directory, usually at:
c:\program files\openecu\ecuflash\rommetadata
Run ecuflash, open File\Options, select Directories\Metadata Directory and set it to the full path to the metadata directory mentioned above.
This will help EcuFlash correctly finding its metadata directory. Usually only "metadata" set in that box and it works because of the executable program relative path is correct but it may not in some cases.
"
#6
Newbie
Thread Starter
Join Date: May 2009
Location: Cincinnati Ohio
Posts: 3
Likes: 0
Received 0 Likes
on
0 Posts
So I finally was able to read the ecu in this 9. I had to reload ecuflash and use a older version. I used v1.29a. I cannot get it to work with the new version no matter what. I cannot get my new 2.0 cable to work either. I used a 1.3 cable. If some one could help me figure out what is going on that would be great. I have got some of the errors here.
Thread
Thread Starter
Forum
Replies
Last Post
CDrinkH2O
General Engine Management / Tuning Forum
13
Apr 28, 2014 08:08 AM
Ceddy
ECU Flash
24
Apr 20, 2011 10:11 AM
funks
ECU Flash
10
Jul 8, 2008 12:50 AM
evo4mad
ECU Flash
180
Jun 7, 2007 05:06 PM