project_skyline

iTrader: (30)

If your having issues converting to 96530706.

Post here

Appauldd

iTrader: (22)

No wait....what was the issue????

I ask because I am running into issues too.

project_skyline

iTrader: (30)

I wasn't able to flash from 94170015 to 96530706. I finally got it. What issues are you having?

Appauldd

iTrader: (22)

I've been trying to get the 96530006 up and running, but I have a ton of addresses wrong. Also, some key tuning elements I use are not supported in the 0006.

The following are missing from 96530006

Idle error tables
Knock Sum Decay Timer
EGR System Enable/Disable

The following tables have wrong addresses

MAF Adjustment
MAF Scaling
all 4 Post Primer tables
Primer Cranking Enrich
all 5 Decel Fuel Cut tables
Airflow/Hz Baro and Air Temp Compensation
Warmup Advance/Retard Activation
Air Temp Trim

Once I can get 0006 to run, I will switch over to tephras rom and give it a shot.

Any assistance would be appreciated.

Thanks.

Paul

tephra

iTrader: (6)

Applaudd - Ca you post up the addresses for those missing tables (from 94170015)

I am found/fixed some for 96530006:

- someone else can merge these into the official 96530006.xml (and set it up with the right names and stuff to match other evo's)

Appauldd

iTrader: (22)

Tephra....sent you an Email.

Here is all of the missing tables.....These are my 94170015 tables


<table name="Idle Stability Timing Control" category="Timing" address="174e" type="2D" level="2" scaling="uint16">
<table name="Settings" type="Static X Axis" elements="3">
<data>Sensitivity</data>
<data>Timing Limit</data>
<data>Untested</data>
</table>
</table>

<table name="Limp Home Table" category="Fuel" address="3797" type="3D" level="2" swapxy="true" scaling="uint8">
<table name="TPS" address="675e" type="X Axis" elements="7" scaling="Volts16"/>
<table name="Engine Speed" address="6776" type="Y Axis" elements="5" scaling="RPM"/>
</table>

<table name="ST Fuel Max Trim" category="Fuel" address="369e" type="2D" level="2" scaling="O2 Trim">
<table name="Engine Temp" address="67a2" type="Y Axis" elements="8" scaling="Temp"/>
</table>

<table name="ST Fuel Min Trim" category="Fuel" address="36ac" type="2D" level="2" scaling="O2 Trim">
<table name="Engine Temp" address="67a2" type="Y Axis" elements="8" scaling="Temp"/>
</table>

<table name="Closed Loop - LT Trim Control" category="Fuel" address="35e5" type="2D" level="2" scaling="LT Trim Hz">
<table name="Conditions" type="Static Y Axis" elements="4">
<data>Low -> Mid</data>
<data>Mid -> Low</data>
<data>Mid -> High</data>
<data>High -> Mid</data>
</table>
</table>

<table name="Closed Loop - LT Trim RPM" category="Fuel" address="35e9" type="2D" level="2" scaling="RPMStatLimit8">
<table name="Conditions" type="Static Y Axis" elements="4">
<data>1</data>
<data>2</data>
<data>3</data>
<data>4</data>
</table>
</table>

<table name="Idle Error - Normal" category="Idle" address="434a" type="2D" level="2" scaling="ISCVSteps">
<table name="Idle Error" address="647e" type="X Axis" elements="9" scaling="RPM"/>
</table>

<table name="Idle Error - A/C On" category="Idle" address="435a" type="2D" level="2" scaling="ISCVSteps">
<table name="Idle Error" address="647e" type="X Axis" elements="9" scaling="RPM"/>
</table>

<table name="Set to 9 by typing 0x9 to remove load limit" address="26694" type="1D" level="2" scaling="Hex16"/>

<table name="KnockSum decay timer" category="Knock Control" address="1784" type="1D" scaling="uint16"/>

<table name="EGR System Enable/Disable" category="Emissions EGR" address="103D" type="1D" level="2" scaling="uint8"/>

tephra

iTrader: (6)

post updated.

let me know if there is anything else

Appauldd

iTrader: (22)

DANG ! ! You are Fast !

Awesome work. Let me know if my 94170015 helped any.

Thanks for you help.

tephra

iTrader: (6)

yeah most of the address were the same.. just had to fix up the axis mainly..

Appauldd

iTrader: (22)

Found some more errors....

<table name="Warmup Advance/Retard Activation" address="41dc">
<table name="Engine Temp" address="681a"/>
</table>

<table name="Air Temp Trim" address="41b2">
<table name="Intake Air Temp" address="689e"/>
</table>

The ST Fuel trims won't show up with values in the fuel side

<table name="ST Fuel Max Trim" category="Fuel" address="369e" type="2D" level="2" scaling="O2 Trim">
<table name="Engine Temp" address="69be" type="Y Axis" elements="8" scaling="Temp"/>
</table>

<table name="ST Fuel Min Trim" category="Fuel" address="36ac" type="2D" level="2" scaling="O2 Trim">
<table name="Engine Temp" address="69be" type="Y Axis" elements="8" scaling="Temp"/>
</table>

The Ignition trim vs... tables have the same address for engine temp and air temp

<table name="Ignition Trim vs Engine Temp" category="Timing" address="41a4" type="2D" level="2" scaling="Percent (128)">
<table name="Engine Temp" address="6aa0" type="Y Axis" elements="8" scaling="Temp"/>
</table>

<table name="Ignition Trim vs Air Temp" category="Timing" address="41b2" type="2D" level="2" scaling="Percent (128)">
<table name="Air Temp" address="6aa0" type="Y Axis" elements="8" scaling="Temp"/>
</table>

tephra

iTrader: (6)

copy the "02 Trim" scaling (from 94170015.xml) into your 96530006.xml

That will fix the SF Fuel trims

Airtemp axis should be 6af0

Appauldd

iTrader: (22)

Yeah I found the scaling was missing.

I believe the addresses are correct for the others, but I get some strange values in the X and Y sides. The tables themselves look to be correct.

Could I just have to past in the correct x and y values???

Appauldd

iTrader: (22)

<table name="Airflow/Hz Baro and Air Temp Compensation" address="3351">
<table name="IAT_Comp/Baro_Bar" address="678e"/>
<table name="MAF Hz" address="67a0"/>
</table>

Are these correct ? ? ?

project_skyline

iTrader: (30)

I just wanted to point out that phenom has a current xml for the v7t6 that has everything current and working.

Im using it and everything seems to be how it should be and functioning properly.

l2r99gst

iTrader: (2)

I also has most, if not all, of those tables that you asked for, but I have the most recent on my laptop. If there are any more outstanding that you need cleared up, let me know which ones, and I can paste what I have on my laptop.