Flex Fuel testing in TephraXMOD V3
#272
#273
EvoM Guru
iTrader: (8)
Not sure about the differences. I can tell you I used a 2010 V3 on this 2011 MR with no issues:
https://www.evolutionm.net/forums/ev...-flexfuel.html
#274
The newest Ecuflash supports this type of flashing without having to bench flash.
Not sure about the differences. I can tell you I used a 2010 V3 on this 2011 MR with no issues:
https://www.evolutionm.net/forums/ev...-flexfuel.html
Not sure about the differences. I can tell you I used a 2010 V3 on this 2011 MR with no issues:
https://www.evolutionm.net/forums/ev...-flexfuel.html
#276
Hi, I am having issues with V3 flex fuel and hope someone can help. I am using the flex converter hardware kit.
The raw ADC and copy of raw ADC are matching the sensor output correctly, but the filtered value is not changing, and the ethanol percentage is clipped to 100% (which does not even match the filtered value I am reading)
See the chart below, the flexconverter kit is in cal mode, so it is stepping through 0,25,50,75,100%. You can see the filtered value is not moving at all.
Here are the labels that I believe are critical to get the ethanol% input working. Am I missing anything?
Does anyone have any insight?
I also see Tephra's documentation says there is a label for max load for signal processing. I do not see the label in ecuflash, unless it is combined with the alternate map load threshold?
Thanks
The raw ADC and copy of raw ADC are matching the sensor output correctly, but the filtered value is not changing, and the ethanol percentage is clipped to 100% (which does not even match the filtered value I am reading)
See the chart below, the flexconverter kit is in cal mode, so it is stepping through 0,25,50,75,100%. You can see the filtered value is not moving at all.
Here are the labels that I believe are critical to get the ethanol% input working. Am I missing anything?
Does anyone have any insight?
I also see Tephra's documentation says there is a label for max load for signal processing. I do not see the label in ecuflash, unless it is combined with the alternate map load threshold?
Thanks
#277
Hi, I am having issues with V3 flex fuel and hope someone can help. I am using the flex converter hardware kit.
The raw ADC and copy of raw ADC are matching the sensor output correctly, but the filtered value is not changing, and the ethanol percentage is clipped to 100% (which does not even match the filtered value I am reading)
See the chart below, the flexconverter kit is in cal mode, so it is stepping through 0,25,50,75,100%. You can see the filtered value is not moving at all.
Here are the labels that I believe are critical to get the ethanol% input working. Am I missing anything?
Does anyone have any insight?
I also see Tephra's documentation says there is a label for max load for signal processing. I do not see the label in ecuflash, unless it is combined with the alternate map load threshold?
Thanks
The raw ADC and copy of raw ADC are matching the sensor output correctly, but the filtered value is not changing, and the ethanol percentage is clipped to 100% (which does not even match the filtered value I am reading)
See the chart below, the flexconverter kit is in cal mode, so it is stepping through 0,25,50,75,100%. You can see the filtered value is not moving at all.
Here are the labels that I believe are critical to get the ethanol% input working. Am I missing anything?
Does anyone have any insight?
I also see Tephra's documentation says there is a label for max load for signal processing. I do not see the label in ecuflash, unless it is combined with the alternate map load threshold?
Thanks
Well I posted a little too soon, lol.
Figured it out. I unplugged the ECU and waited a few seconds and reconnected, the values in the V filtered and ethanol % cleared.
Also, the filter does not run unless the fuel pump is running.
Maybe this will help someone else with a similar issue.
#280
#281
Blessings i don't know if anyone can help me, i make my Lancer 2009 4b11 turbo about like a month ago, first up my tuner just took the oem ecu and replace the rom to evo x rom now my rpm idle is always on 2000 i hate my car lol and every tuner i ask said to me if my car doesn't have abs the speedometer and the tpms won't work, i don't know about tuning but there isn't a way to replace reading from the abs to reading from the speed sensor?
#282
purchase TephraXMOD V3
Hi, David aka Tephra,
I tried to reach you via private message, but your inbox overload))))) So, it's why I'm contacting you here.
My name is Roman Shovkun; I paid on Aug 15, 2019, for TephraXMOD V3 for my Mitsubishi Evo X.
The PayPal Transaction ID 7N583787N03108505, if needed I can send you the receipt.
Please let me know when I can expect to receive it or how I can get it?
Thank you!
Best Regards,
Roman Shovkun aka Lobzik
Kiev, Ukraine
email: rshovkun@gmail.com
cell: +380667854398
Skype: ramzesvelikiy
#283
Sorry, for the off top.
Hi, David aka Tephra,
I tried to reach you via private message, but your inbox overload))))) So, it's why I'm contacting you here.
My name is Roman Shovkun; I paid on Aug 15, 2019, for TephraXMOD V3 for my Mitsubishi Evo X.
The PayPal Transaction ID 7N583787N03108505, if needed I can send you the receipt.
Please let me know when I can expect to receive it or how I can get it?
Thank you!
Best Regards,
Roman Shovkun aka Lobzik
Kyiv, Ukraine
email: rshovkun@gmail.com
cell: +380667854398
Skype: ramzesvelikiy
Hi, David aka Tephra,
I tried to reach you via private message, but your inbox overload))))) So, it's why I'm contacting you here.
My name is Roman Shovkun; I paid on Aug 15, 2019, for TephraXMOD V3 for my Mitsubishi Evo X.
The PayPal Transaction ID 7N583787N03108505, if needed I can send you the receipt.
Please let me know when I can expect to receive it or how I can get it?
Thank you!
Best Regards,
Roman Shovkun aka Lobzik
Kyiv, Ukraine
email: rshovkun@gmail.com
cell: +380667854398
Skype: ramzesvelikiy
All, set!!!
David responded via email.
Thank you!
Thread
Thread Starter
Forum
Replies
Last Post
Lightsaber
Evo X Engine Management / Tuning Forums
2
Jul 30, 2015 07:57 PM