Unbeatable Pricing: Magnus and MAP Intake Manifolds!
#1
Unbeatable Pricing: Magnus and MAP Intake Manifolds!
Please contact us for unbeatable pricing on these great options!
AIM - Adam At MAP
Phone - 763-545-3800
Email - Adam@maperformance.com
PM - Click CLICK HERE TO PM US!
Click here for more information or to place and order for our Rev2 and Rev3 intake manifolds!
Click the dyno chart for more information on the amazing 49whp gain realized from the MAPerformance Rev3 intake manifold! We are proud to be a part this record breaking project!
Magnus Cast Aluminum Intake Manifold
Includes adapter to suit stock or 75mm+ throttle bodies / throttle body gasket / heat barrier gasket to head / hardware!
Over 10 years ago, Magnus Motorsports released its first Sheet Metal Intake Manifold into the market place and it quickly became the standard within the Mitsubishi Racing community. After almost 2 years in development, we would like to introduce you to the next big thing. The Magnus Motorsports Cast Intake Manifold.
Magnus designed this one from a fresh sheet of paper. Out of over a dozen prototypes, endless testing and perfecting, the Magnus Cast Intake Manifold was born. They applied our years of experience from crafting thousands of sheet metal intakes and once again have raised the bar for power and quick response. By applying a unique design and a massive 5L plenum, this cast manifold means big power and big power sooner!
Cast in A356 Aluminum with a wall thickness of 3/16"; the Plenum shape features a varying contoured tapered profile at a volume of 5 liters. The runners themselves are completely revolutionary in their design; featuring an integrated velocity stack that gradually transitions into the head port profile. It was designed entirely against the shape of the original cylinder head port taking advantage the 10° port entry of the EVO head maintaining un-interrupted laminar flow. The Magnus Cast Intake Manifold will work with throttle bodies from stock right up to 100mm and have seen consistent gains from 30 awHp to 52 awHp with varying setups. Transient boost response is exceptional and it can bolt together in a stock location if required while still being able to be used on a full blown race application.
Cast Intake Manifold Features:
- 2 years of research and development
- Cast from A356-T6 Aluminum Alloy
- High quality casting gives a superior surface finish
- Enhanced flow dynamics utilizing CAD Modeling & CFD simulation
- Flowbenched and dynamically tested
- Dynotested proven up to 50 HP / Stock turbo gains up to 40HP
- Ability to flow 100 lb/min (1000 HP) of air at 60PSI while maintaining equal flow distribution
- Can be installed in stock location with clearance for original battery (with adaptor)
- 15 degree entry to the throttle body facilitates intercooler plumbing
- Can be configured for 8 injector setup.
- Fits factory fuel rail or Magnus high flow fuel rails
- 5L plenum with contoured velocity stacks molded into the floor for huge top end and minimal turbulence
- Magnus Quality and Lifetime warranty
Independent Testing & Reviews
Installation Pics
Dyno Comparison to Stock Intake Manifold and Magnus Sheet Metal
Magnus Cast Intake + QTP o2 Dump = 83whp
ETS 57 Trim Kit + Magnus Cast Mani = 34whp
Amazing Magnus Cast Intake test +35hp
2nd Magnus Test same great results 25hp
Buschur Racing Flow Bench / Dyno Testing
Please contact us for unbeatable pricing on these great options!
AIM - Adam At MAP
Phone - 763-545-3800
Email - Adam@maperformance.com
PM - Click CLICK HERE TO PM US!
Installation Pics
Dyno Comparison to Stock Intake Manifold and Magnus Sheet Metal
Magnus Cast Intake + QTP o2 Dump = 83whp
ETS 57 Trim Kit + Magnus Cast Mani = 34whp
Amazing Magnus Cast Intake test +35hp
2nd Magnus Test same great results 25hp
Buschur Racing Flow Bench / Dyno Testing
Please contact us for unbeatable pricing on these great options!
AIM - Adam At MAP
Phone - 763-545-3800
Email - Adam@maperformance.com
PM - Click CLICK HERE TO PM US!
Last edited by maperformance; May 4, 2009 at 09:52 AM.