View Poll Results: WAS THIS WORTH MY TIME TO COMPILE ALL THIS TO 1 THREAD?
HECK YEAH
906
93.21%
nope
66
6.79%
Voters: 972. You may not vote on this poll
Official Jdm Exhaust Fitment Thread
I need help with Greddy TI. I have JDM + Greddy TI but it seems to touch the bumper, not at the tip but the big tube( it goes like 3" piping, humongous tube and 3" piping+rolled bluish lips)
Anyone with the same setup, please post the a picture? I need to know what is wrong. Thank you.
Anyone with the same setup, please post the a picture? I need to know what is wrong. Thank you.
If you see the last picture, my jdm bumper seems to touch that 'carbon tube', but mine is the Greddy TI. Is it because of the test pipe/DP?
Thread Starter
Evolved Member
Joined: May 2007
Posts: 884
Likes: 0
From: W SUNSET & PCH
no its because its a usdm exhaust on a jdm bumper. you need to take it to a exhaust shop and have them re do the hangers and shorten it about 2 inches.
Thread Starter
Evolved Member
Joined: May 2007
Posts: 884
Likes: 0
From: W SUNSET & PCH
Any tips for that?
Thread Starter
Evolved Member
Joined: May 2007
Posts: 884
Likes: 0
From: W SUNSET & PCH
if it is slightly touching the JDM bumper cut out, then have the exhaust hangers modded by moving them slightly until it centers. however, while you are doing this (if you choose to) then have it shortened up about an inch.
and it wont burn the bumper for a while.
unless i am miss-understanding you, if its greddy (regaurdless of it being a TI or TIC or ching ling yang) it is for a USDM bumper. not a JDM bumper if it said TRUST TI then it would fit absolutely perfect like (USERNAME) DogDealer's.
if it is slightly touching the JDM bumper cut out, then have the exhaust hangers modded by moving them slightly until it centers. however, while you are doing this (if you choose to) then have it shortened up about an inch.
and it wont burn the bumper for a while.
if it is slightly touching the JDM bumper cut out, then have the exhaust hangers modded by moving them slightly until it centers. however, while you are doing this (if you choose to) then have it shortened up about an inch.
and it wont burn the bumper for a while.
Thread Starter
Evolved Member
Joined: May 2007
Posts: 884
Likes: 0
From: W SUNSET & PCH
dont pay more than 100 bucks but, dot expect to pay less tan 50.
Thread Starter
Evolved Member
Joined: May 2007
Posts: 884
Likes: 0
From: W SUNSET & PCH
no pics, you will be able to get the bumper on but you should drive straight to a muffler shop pay 50 bucks and have it shortened so it fits correctly.
bottom line.
if its USDM IT DOES NOT FIT RIGHT. it will go on but it will either rub or stick out and look like a honda or other half *** modded car.
IF ITS USDM IT NEEDS TO BE MODDED PERIOD. some just fit a little bit better but just spend 50 bucks on getting it modded. its SOOOOOOOOOOO WORTH IT!
bottom line.
if its USDM IT DOES NOT FIT RIGHT. it will go on but it will either rub or stick out and look like a honda or other half *** modded car.
IF ITS USDM IT NEEDS TO BE MODDED PERIOD. some just fit a little bit better but just spend 50 bucks on getting it modded. its SOOOOOOOOOOO WORTH IT!
