Out of toe adjustment?
#1
Out of toe adjustment?
Had an alignment done and found I'm out of toe adjustment at the rear.
the car is lowered a bit. Camber is within spec.
Do our cars REALLY have such limited availability of movement back there?
On the bright side, my caster in on point.
the car is lowered a bit. Camber is within spec.
Do our cars REALLY have such limited availability of movement back there?
On the bright side, my caster in on point.
#4
On my last visit to the Mitsu dealer for an alignment, they told me I was out of toe and camber adjustment in the front. My suspension is completely stock. I've never owned a vehicle before where the OEM hardware became insufficient to keep the car in spec during its lifetime.
The dealer told me they would order newer hardware (bolts) which would allow further adjustment at a cost of $30 each plus installation. This pissed me off, as I didn't feel like I should be footing the bill for the fact that Mitsu used inadequate running gear from the factory...I just walked away.
The dealership has since closed, but I still need to do something about the alignment as my relatively new Hankooks are getting beaten up since I drive 50 miles round-trip to work each day...
The dealer told me they would order newer hardware (bolts) which would allow further adjustment at a cost of $30 each plus installation. This pissed me off, as I didn't feel like I should be footing the bill for the fact that Mitsu used inadequate running gear from the factory...I just walked away.
The dealership has since closed, but I still need to do something about the alignment as my relatively new Hankooks are getting beaten up since I drive 50 miles round-trip to work each day...
#8
Evolved Member
iTrader: (7)
I would take the car somewhere else. Firestone in general sucks for alignments from my personal experience.
How low is your car? That plays a little part, but it should be able to get closer than that. I think if you add camber you get get a little more toe adjustment, but I don't think you should go much beyond where you already are. If all else fails, you could get some adjustment toe arms such as the meagan ones.
I just think the tech probably didn't know what they were doing.
How low is your car? That plays a little part, but it should be able to get closer than that. I think if you add camber you get get a little more toe adjustment, but I don't think you should go much beyond where you already are. If all else fails, you could get some adjustment toe arms such as the meagan ones.
I just think the tech probably didn't know what they were doing.
#9
I have free alignments from Firestone, so it's hard for me to pay and go elsewhere unless I find there is a real problem.
My car is lowered a bit in the rear. Not sure how much. I lowered the car as much as I could while still keeping control arms above parallel with the ground. I won't be adding camber until I start tracking the car again. Tech says the adjustments are maxed out I haven't been under the car to see for myself, yet. But it's kinda hard to mess that up. Not that I'm saying it's impossible if they are retarded enough.
My car is lowered a bit in the rear. Not sure how much. I lowered the car as much as I could while still keeping control arms above parallel with the ground. I won't be adding camber until I start tracking the car again. Tech says the adjustments are maxed out I haven't been under the car to see for myself, yet. But it's kinda hard to mess that up. Not that I'm saying it's impossible if they are retarded enough.
#10
Evolved Member
iTrader: (7)
Yeah I have the lifetime alignments but they couldn't get it right so I just ate the cost and went elsewhere. Best decision I made.
I agree with others that you should have more adjustment left unless something was damaged at some point in the rear or you have a bad bushing/s.
I agree with others that you should have more adjustment left unless something was damaged at some point in the rear or you have a bad bushing/s.
#14
Evolved Member
a bit OT... but I am always wondering why people throw out OE spherical bushings from the evo and install poly bushings instead?