How to Blackout Headlight housing (even though I left a bit of chrome)
#16
Evolved Member
iTrader: (4)
Join Date: Feb 2008
Location: Edmonton, Alberta
Posts: 610
Likes: 0
Received 0 Likes
on
0 Posts
Guys, you can't do this with a non-HID housing.
You won't have any light output. The reason it works is because the projector is left as is, but the chrome surround is painted. I painted my DRL reflector too, but that's because I don't use the DRL.
(OP, again, nice job)
You won't have any light output. The reason it works is because the projector is left as is, but the chrome surround is painted. I painted my DRL reflector too, but that's because I don't use the DRL.
(OP, again, nice job)
#18
Evolving Member
Thread Starter
Join Date: Oct 2008
Location: NC
Posts: 152
Likes: 0
Received 0 Likes
on
0 Posts
You could paint the trim pieces to sorta get the same effect however you would still be left with a lot of chrome due to the lights needing the reflectors. It would help some but the look may not be as dramatic. But then again it may be. I'd be interested to see what the non-HID lights look like painted up.
#23
#24
Evolving Member
iTrader: (4)
Join Date: Jun 2009
Location: charleston
Posts: 276
Likes: 0
Received 0 Likes
on
0 Posts
I did mine fri night. Started at 8pm and had them ready to reinstall at 2am. Waited till sat morning to install them. I did not have to sand or primer anything using plasti dip spray paint (from lowes). And they turned out awesome. Ill post pics in a few. Also i plast dipped my middle hood scoop which looks much better imo. This is not the average joe mod....you take a good chance of screwing up expensive lights if you dont know what your doing.
Last edited by evoooo; Oct 26, 2009 at 02:53 PM.
#27
Evolving Member
iTrader: (4)
Join Date: Sep 2008
Location: Alabama
Posts: 478
Likes: 0
Received 0 Likes
on
0 Posts
If you dont want to paint the whole amber turn signal, make a piece of strip and place on each one, then paint, so light will still shine through. The reflector inside the actual bulb dome doesnt have to be stock, it jst helps reflect light.
#28
Evolving Member
Thread Starter
Join Date: Oct 2008
Location: NC
Posts: 152
Likes: 0
Received 0 Likes
on
0 Posts
evoooo the headlights turned out nice. Too dark for my tastes but looks pretty slick on the WW.
As far as prepping the surface no sanding is required. I just made sure the surface was clean of oils by lightly washing things first.
This job isn't that difficult. The only hard and wierd part is pulling the housing apart after baking. As long as you take your time and don't put enough leverage to crack the lens you should be fine. If the glue isn't soft enough bake them for another 3-5 minutes and try again.
As for an update my lights have gone trough the seasonal changes and a hell of a lot of rain and there still is no fogging, condensation, or discoloration of the headlights. Looks like my silicone sealant is doing its job.
As far as prepping the surface no sanding is required. I just made sure the surface was clean of oils by lightly washing things first.
This job isn't that difficult. The only hard and wierd part is pulling the housing apart after baking. As long as you take your time and don't put enough leverage to crack the lens you should be fine. If the glue isn't soft enough bake them for another 3-5 minutes and try again.
As for an update my lights have gone trough the seasonal changes and a hell of a lot of rain and there still is no fogging, condensation, or discoloration of the headlights. Looks like my silicone sealant is doing its job.