Evo VIII from Austria
#16
Newbie
Thread Starter
Again, something new for my Evo
Charge Speed CT9A Hood Duct in FRP, orderer it from RHD Japan. Was delivered in three weeks. Everything you need for the Install is included, like screws and washers. Also a nice cataloque and a sticker.
The duct is white primed, i think i will paint it in gloss black. Louver is already installed. First fitment test was good, i would say 9/10 points. I havent tigthened the screws complete, so there is a slight gap at the moment.
Here are pics for you:
Charge Speed CT9A Hood Duct in FRP, orderer it from RHD Japan. Was delivered in three weeks. Everything you need for the Install is included, like screws and washers. Also a nice cataloque and a sticker.
The duct is white primed, i think i will paint it in gloss black. Louver is already installed. First fitment test was good, i would say 9/10 points. I havent tigthened the screws complete, so there is a slight gap at the moment.
Here are pics for you:
Last edited by Sascha; Feb 6, 2017 at 11:56 PM.
#17
Newbie
Thread Starter
So, i bought my Evo some gifts, Evo IX Taillights and Headlights. Small but effective modification. Rexpeed Side Spats and an ECUFlash Cable. Spats, Headlights and Cable should arrive on Dezember 30.
I also think on painting the mirros black, could look good.
I also think on painting the mirros black, could look good.
Last edited by Sascha; Feb 6, 2017 at 11:56 PM.
#19
EvoM Staff Alumni
iTrader: (3)
Again, something new for my Evo
Charge Speed CT9A Hood Duct in FRP, orderer it from RHD Japan. Was delivered in three weeks. Everything you need for the Install is included, like screws and washers. Also a nice cataloque and a sticker.
The duct is white primed, i think i will paint it in gloss black. Louver is already installed. First fitment test was good, i would say 9/10 points. I havent tigthened the screws complete, so there is a slight gap at the moment.
Here are pics for you:
Charge Speed CT9A Hood Duct in FRP, orderer it from RHD Japan. Was delivered in three weeks. Everything you need for the Install is included, like screws and washers. Also a nice cataloque and a sticker.
The duct is white primed, i think i will paint it in gloss black. Louver is already installed. First fitment test was good, i would say 9/10 points. I havent tigthened the screws complete, so there is a slight gap at the moment.
Here are pics for you:
Looks great if you dont mind me saying Not sure how my EVO got posted up on your post
Last edited by MinusPrevious; Dec 28, 2015 at 07:26 PM.
#22
Newbie
Thread Starter
Thank you, i run 245/40/17 Conti Sport Contact 5P tires, but i´m looking for 18" right now. But at first i will drive the 17" until they ran out of thread
#24
Newbie
Thread Starter
#25
Newbie
Thread Starter
Long time no see, but over the winter some things got new.
Invidia Turbo Outlet
AEM Wideband
VDO Boost Gauge
VDO Oil Pressure Gauge
PU-Front Lip
Zacklee Cam Cover
PFC Z-Rated Pads all around
RossSport Slotted Discs all around
Steel Braided Brake Lines all around
Airbox Mod
EvoWorks LICP
ETS 3" Intercooler
Setrab Oilcooler
Spal Fan
Torque Solutions 4-piece Engine Mounts
Evo IX Headlights
Evo IX Taillights
Rexpeed Bonnet Vent
Rexpeed Carbon Side Spats
Rexpeed Carbon Air Ducts
Now the car gets remapped and then is finished for 2016.
Future plans are, a FP Ported Manifold and get my IX-Turbo rebuild with a billet compressor wheel with extended tips and a set of 18" Enkei Wakasa´s.
Invidia Turbo Outlet
AEM Wideband
VDO Boost Gauge
VDO Oil Pressure Gauge
PU-Front Lip
Zacklee Cam Cover
PFC Z-Rated Pads all around
RossSport Slotted Discs all around
Steel Braided Brake Lines all around
Airbox Mod
EvoWorks LICP
ETS 3" Intercooler
Setrab Oilcooler
Spal Fan
Torque Solutions 4-piece Engine Mounts
Evo IX Headlights
Evo IX Taillights
Rexpeed Bonnet Vent
Rexpeed Carbon Side Spats
Rexpeed Carbon Air Ducts
Now the car gets remapped and then is finished for 2016.
Future plans are, a FP Ported Manifold and get my IX-Turbo rebuild with a billet compressor wheel with extended tips and a set of 18" Enkei Wakasa´s.
Last edited by Sascha; Feb 6, 2017 at 11:58 PM.
#26
Newbie
Thread Starter
Got my Evo on the Dyno for the baseline, made 351PS/500Nm with the EMD-ECU which will be changed for an OEM VIII-ECU with Tephra Mod which will be done by next week. In the meantime i orderer a Rexpeed Type-3 Carbon Trunk Spoiler.
Last edited by Sascha; Feb 6, 2017 at 11:58 PM.
#30
Newbie
Thread Starter
Finished for 2016. Made 503PS/513Nm on the Dyno.
Next will be 18" Rims, FP Ported Manifold, Kelfrod 272 Cams or GSC S2 and a optimized Evo IX Turbo. But that will be in 2017
Next will be 18" Rims, FP Ported Manifold, Kelfrod 272 Cams or GSC S2 and a optimized Evo IX Turbo. But that will be in 2017
Last edited by Sascha; Feb 6, 2017 at 11:59 PM.