I'm going to part out my build.I will let the parts sit and rot before I give the stuff away. I have receipts for EVERYTHING. Most of this stuff was purchased from Burd@MAPerformance.

Stuff I will take as acceptable trades:
Stock or built 2.0 MUST BE AN 8 BLOCK
HTA Green or BBK
Exedy Twin
Built Head

MAPerformance built 2.4 Stage 2

I'm looking to make a deal on this ASAP. I can do a package deal for people looking to drop this right in with the proper supporting mods. I can include the cam gears, head gasket, AMS oil pan, and Kiggly HLA for an additional $850 and you'll save on shipping too.


4G64 block and Crank
Wiseco 1400HD pistons 8:8:1 compression
MAP Howards Rods
ACL bearings
ARP main Studs
OEM front cover
OEM water pump
OEM timing belt pulleys
OEM seals
OEM oil squirters machined into the 4g64 block.
This block has 2800 miles on it. It was broken in 110% properly and had less than 3% leakdown before I took it out of the the car. I had a clutch issue that made park the car for a while. I never got a final tune on the car. I was running a Precision 5857 on 25psi making a little over 420whp. So there was not a lot of stress on the block. As we all know, this combo is capable of 1000whp.
I'm looking to get $2500 or $1500 and your stock block. Plus paypal fees and shipping. I can ship this on my old Shep trans box, which is how I got it from MAP.

SOLD TO SILK

Driven Innovations medium plenum intake manifold. This is an awesome piece. It is one of the best manifolds hands down and did awesome in Buschurs intake manifold shoot out. It is flanged for a stock throttle body that has been bored to 65mm.
$700 plus paypal and shipping. SOLD to psphinx81

AMS wet sump oil pan. It will include the oil pan pick-up, crank scraper modded for a 100mm crank, and the oil pan baffle. $500 plus shipping and paypal fees.

SOLD TO SILK

Fluidampr Crank Pulley. Replaces the stock pulley. Made in USA and it's a family owned company. This is good for any engine not running balance shafts. Helps prolong bearing life. $220 shipped. SOLD to Svendiesel

Kiggly HLA $150 shipped/paypal SOLD TO SILK
ETS recirc pipe $30 shipped SOLD .
BLE manual timing belt tensioner $80 shipped
Tactrix boost control solenoid with harness $75 shipped
Easy squeeze connectors and pigtails for injectors $30 shipped



Power Enterprise 87mm head gasket. This seals MAP's 2.4. So it's good enough for your build. $150 shipped.
SOLD TO SILK

Coil on Plug DIY kit. I bought the plate,wire, connectors, and sheathing from spoolinup. I also have Denso coils that are the correct length and have the pigtails. Coils have 18k miles on them .SOLD to Sphinxof2006

Vibrant 2.5" coupler tube in black. 29.5" left. $40 shipped


GSC springs, seats, and retainers. Low miles like the rest of the parts. $350 shipped and paypal'd.
SOLD TO Christian

Comp 280 cams. $200 shipped.
Sold to Christian

AVID race mounts $200 shipped plus paypal. both side mounts and rear motor mount. Comes with all the brackets you need.
Traded to TheDark20

All this stuff is best offer. I will be listing a ton more stuff as time goes on. But this is the first round of parts. Any questions please PM ME.

 

If you still have the motor end of JAN i will get this for sure.

 

when did you get the IM? as far as i know DI makes a large and small plenum IM not a medium lol

 

I apologize, that was my mistake. It is a small plenum manifold with a 65mm throttle body inlet.

 

would the valve cover fit a MIVEC head?

 

Erics a very good friend of mine, I can vouch for his honesty and integrity. No one will be disappointed with anything they get from this part out.

 

just bought the DI intake manifold!

 

and i think i just got the block....

 

Lots of interest. Keep the PM's coming.

 

sent you a pm. no interest?

 

Sorry about that. I replied back. I must have overlooked it.

 

No it will not. It's for an 8.

All pm's have been answered. Thanks for the interest.

 

Motivated seller.

 

are those 5spd motor mounts?

 

awesome guy, great to deal with