Mark this thread as Unsold
FS: PSI3/Forge Motorsport ECU Data Monitor
#1
Evolved Member
Thread Starter
iTrader: (23)
Join Date: Jun 2004
Location: Orlando FL
Posts: 1,240
Likes: 0
Received 0 Likes
on
0 Posts
FS: PSI3/Forge Motorsport ECU Data Monitor
THIS ITEM HAS BEEN SOLD.
THANK YOU FOR YOUR INTEREST.
This is a one-of-a-kind product. The only unit of it's kind available in the USA.
This product is no longer available in the US in this configuration for the Mitsubishi Evo application.
Manufactured by: PSI3 of England
For: Forge Motorsport UK/US
--------------------------------------------------------------------------------------------------------
Reads and displays OBD2 diagnostic information read by the ECU in real time.
Including:
Inlet Temp.
Boost Pressure
EGT
Oil Pressure
Oil Temp.
Coolant Temp.
RPM
Real Vehicle Speed
Battery Voltage
Air/Fuel Ratio
Low/High Warning Alarm settings for all functions.
Clock
Also:
Water Injection setup option
Shift Light setup option
Ability to read and clear fault codes
4 Data display pages:
Each diaplay page shows 4 different perameters of diagnostics.
Additional Defi sensors MAY BE REQUIRED for accurate readings of certain functions not read by the ECU. (Boost pressure, EGT, Oil Temp., Oil Pressure, Coolant Temp.) Additional sensors ARE NOT included.
ONLY Defi electronic sensors can be used with this product. The data monitor is configured to only read Defi sensors.
---------------------------------------------------------------------------------------
This product will be shipped with the following:
PSI3 OBD2 ECU Data Monitor - Red VFD Screen (Vacuum Flourecent Display)
Custom modified Mitsubishi cubby hole
OBD2 Connector Harness
Harness Adapter for External Sensors
Instructions
Product will be supplied with Red colored buttons.
The display screen can be modified to a different color if desired. Transparent colored vinyl or colored plexiglass can be used, but is not included.
--------------------------------------------------------------------------------------------------------
Asking Price:
THIS ITEM HAS BEEN SOLD.
Payment options:
Credit Card
Check (payment must clear before product ships)
Money Order (payment must clear before product ships)
Paypal
--------------------------------------------------------------------------------------------------------
All sales are final.
Forge Motorsport will not honor any warranty nor service claims on this product. PSI3 in the UK will need to be contacted for any warranty and/or service related issues.
THANK YOU FOR YOUR INTEREST.
This is a one-of-a-kind product. The only unit of it's kind available in the USA.
This product is no longer available in the US in this configuration for the Mitsubishi Evo application.
Manufactured by: PSI3 of England
For: Forge Motorsport UK/US
--------------------------------------------------------------------------------------------------------
Reads and displays OBD2 diagnostic information read by the ECU in real time.
Including:
Inlet Temp.
Boost Pressure
EGT
Oil Pressure
Oil Temp.
Coolant Temp.
RPM
Real Vehicle Speed
Battery Voltage
Air/Fuel Ratio
Low/High Warning Alarm settings for all functions.
Clock
Also:
Water Injection setup option
Shift Light setup option
Ability to read and clear fault codes
4 Data display pages:
Each diaplay page shows 4 different perameters of diagnostics.
Additional Defi sensors MAY BE REQUIRED for accurate readings of certain functions not read by the ECU. (Boost pressure, EGT, Oil Temp., Oil Pressure, Coolant Temp.) Additional sensors ARE NOT included.
ONLY Defi electronic sensors can be used with this product. The data monitor is configured to only read Defi sensors.
---------------------------------------------------------------------------------------
This product will be shipped with the following:
PSI3 OBD2 ECU Data Monitor - Red VFD Screen (Vacuum Flourecent Display)
Custom modified Mitsubishi cubby hole
OBD2 Connector Harness
Harness Adapter for External Sensors
Instructions
Product will be supplied with Red colored buttons.
The display screen can be modified to a different color if desired. Transparent colored vinyl or colored plexiglass can be used, but is not included.
--------------------------------------------------------------------------------------------------------
Asking Price:
THIS ITEM HAS BEEN SOLD.
Payment options:
Credit Card
Check (payment must clear before product ships)
Money Order (payment must clear before product ships)
Paypal
--------------------------------------------------------------------------------------------------------
All sales are final.
Forge Motorsport will not honor any warranty nor service claims on this product. PSI3 in the UK will need to be contacted for any warranty and/or service related issues.
Last edited by Mike@Forge; Aug 11, 2005 at 02:43 PM.
#2
Evolved Member
iTrader: (17)
Join Date: Sep 2003
Location: San Jose, CA
Posts: 1,797
Likes: 0
Received 0 Likes
on
0 Posts
So any ideas on about how much these additional sensors would cost? Also, the OBD port plug is an obvious plug'n'play setup but the other pinout, that would need to be manually wired correct?
I've never seen this item before so excuse my newbness. =)
I've never seen this item before so excuse my newbness. =)
#3
Evolved Member
Thread Starter
iTrader: (23)
Join Date: Jun 2004
Location: Orlando FL
Posts: 1,240
Likes: 0
Received 0 Likes
on
0 Posts
Additonal sensors will very in price depending on where they are purchased from but retail prices range from $70-$175 per sensor.
I found that boost pressure, oil pressure, oil temp., coolant temp., and EGT sensors will be required given that the Evo ECU's don't display these functions very accurately.
--------------------------------------------------------------------------------------------------------
The OBD2 connector is indded plug-n-play. The green connector will plug into the back of the unit and it will power itself on each time the ignition is turned on and it will power itself off with a "Goodbye" message each time the ignition is turned off.
There is no need to wire up an external power source. The unit is powered through the OBD2 port.
---------------------------------------------------------------------------------------
The second larger connector is only for the external sensors and will require that each sensor be wired to it. The pin-outs are specified in the supplied instructions and should take no more than 5 minutes and little to no electrical experience is required.
--------------------------------------------------------------------------------------------------------
Don't worry about not knowing about this product. Only a handful of people have ever seen it!
Like I said, it's a custom built one-off component.
I found that boost pressure, oil pressure, oil temp., coolant temp., and EGT sensors will be required given that the Evo ECU's don't display these functions very accurately.
--------------------------------------------------------------------------------------------------------
The OBD2 connector is indded plug-n-play. The green connector will plug into the back of the unit and it will power itself on each time the ignition is turned on and it will power itself off with a "Goodbye" message each time the ignition is turned off.
There is no need to wire up an external power source. The unit is powered through the OBD2 port.
---------------------------------------------------------------------------------------
The second larger connector is only for the external sensors and will require that each sensor be wired to it. The pin-outs are specified in the supplied instructions and should take no more than 5 minutes and little to no electrical experience is required.
--------------------------------------------------------------------------------------------------------
Don't worry about not knowing about this product. Only a handful of people have ever seen it!
Like I said, it's a custom built one-off component.
Last edited by Mike@Forge; Aug 8, 2005 at 11:57 AM.
Thread
Thread Starter
Forum
Replies
Last Post
DrivelineSales
Lancer Ralliart Vendor Classifieds
4
Jun 20, 2011 04:50 PM
Mike@Forge
Evo How To Requests / Questions / Tips
27
Oct 20, 2009 07:54 PM
Mike@Forge
Evo Engine / Turbo / Drivetrain
14
Oct 21, 2005 02:19 PM
RAllen
For Sale - Interior / Exterior / Sound / Styling
5
Apr 28, 2005 11:39 AM