EvolutionM - Mitsubishi Lancer and Lancer Evolution Community
Inside shot. I drilled this in place with the engine assembled. I just removed the oil pan and baffle/windage trays.
Inside shot. I drilled this in place with the engine assembled. I just removed the oil pan and baffle/windage trays.
0 2022/07/04 15:06:15
12AN (1/2NPT base) fitting installed into the front balance shaft tunnel. Installing onto the front of the block is critical because the oil is already flung onto the back of the block. The front of the block should be relatively "dry".
12AN (1/2NPT base) fitting installed into the front balance shaft tunnel. Installing onto the front of the block is critical because the oil is already flung onto the back of the block. The front of the block should be relatively "dry".
0 2022/07/04 15:06:13
0 2022/06/11 15:05:45
0 2022/06/08 14:17:06
0 2022/06/08 14:17:03
0 2022/06/08 14:17:02
0 2022/06/08 14:16:59
0 2022/06/06 15:08:01
extra holes drilled into the baffle plates to help with draining oil that gets above them
extra holes drilled into the baffle plates to help with draining oil that gets above them
0 2022/06/05 00:59:58
fuel tank foam installed to help with oil being pushed out the breather lines
fuel tank foam installed to help with oil being pushed out the breather lines
0 2022/06/05 00:59:53
Hypertune cover with no baffles installed
Hypertune cover with no baffles installed
0 2022/06/05 00:59:49
0 2022/06/05 00:56:36
0 2022/06/02 14:07:38
5" diameter catch can. Around 2.5L capacity. Internal baffling to pull oil vapour from the air.
5" diameter catch can. Around 2.5L capacity. Internal baffling to pull oil vapour from the air.
0 2022/06/02 14:07:35
0 2022/06/02 14:07:33
0 2022/05/31 14:10:50
Caliper only replacement kit from ENDLESS
Caliper only replacement kit from ENDLESS
0 2022/05/31 14:08:10
0 2022/05/25 14:32:09
0 2022/05/16 17:47:24
0 2022/05/16 17:42:41
0 2022/05/16 17:36:38
0 2022/05/01 14:58:18
This is what they will look like after Op.2 has been completed. It's ready to weld into the oil pan.
This is what they will look like after Op.2 has been completed. It's ready to weld into the oil pan.
0 2022/03/17 01:10:56
45 bases finished op.1 in the CNC machine
45 bases finished op.1 in the CNC machine
0 2022/03/17 01:10:53
Old Rev1 design versus Rev2 design. Rev two is faster to machine and has less burrs that needs to be worked. Overall a better piece.
Old Rev1 design versus Rev2 design. Rev two is faster to machine and has less burrs that needs to be worked. Overall a better piece.
0 2022/03/17 01:10:51
Tetris anyone?
Tetris anyone?
0 2022/03/17 01:10:50
2 pieces of steel loaded into the machine vices, ready to go
2 pieces of steel loaded into the machine vices, ready to go
0 2022/03/17 01:10:30
CNC working it's magic
CNC working it's magic
0 2022/03/17 01:10:27
Pink section is the difference of oil pressure between the Infinite Evo oil pan and the competitor
Pink section is the difference of oil pressure between the Infinite Evo oil pan and the competitor
0 2022/03/03 10:38:26
0 2022/03/03 00:22:52
0 2022/01/12 13:50:50
0 2022/01/12 13:50:47
0 2021/08/28 13:11:06
0 2021/08/28 13:11:04
0 2021/08/28 13:11:02
InfiniteEvo new oil pressure regulator, fresh ground-up design
InfiniteEvo new oil pressure regulator, fresh ground-up design
0 2021/08/28 13:11:00
0 2021/08/28 13:08:20
0 2021/08/28 13:08:14
0 2021/08/28 13:08:08
0 2021/08/28 13:08:02