Omni 4 bar MAP sensor ROM compatibility settings for USDM Evo 8/9
#259
Evolved Member
iTrader: (8)
Quick question, After installing the omni4bar I noticed my boost has went up from tuned boost 25psi 3port,, to around 28 psi did i do something wrong
And I also noticed that the Map Sensor Maps are highlighted Blue instead of black
dose that mean that they are not enabled,,
And I also noticed that the Map Sensor Maps are highlighted Blue instead of black
dose that mean that they are not enabled,,
#260
Newbie
I have my settings for the 8895 rom in post #1, reading about -7 vac on ecuflash. Just installed an aem boost gauge with the 5 bar sensor, I’m reading -13 vac at idle. Car is a stock motor stock mivec cams. Do I need to adjust something to get them to match up? I assume the brand new aem gauge is the corrext one here need these to line up properly
#261
Evolving Member
iTrader: (2)
I have my settings for the 8895 rom in post #1, reading about -7 vac on ecuflash. Just installed an aem boost gauge with the 5 bar sensor, I’m reading -13 vac at idle. Car is a stock motor stock mivec cams. Do I need to adjust something to get them to match up? I assume the brand new aem gauge is the corrext one here need these to line up properly
Are they both in the same units?
Some gauges go to InHg in vacuum.
-13InHg is -6.4ish psi.
So that may be the case.
The following users liked this post:
GG06MR (Oct 8, 2019)
#262
Newbie
#263
Evolved Member
iTrader: (41)
Idk about the AEM, but I've never seen the Omni 4 bar show the correct values for vacuum in Evoscan. I've heard others say that it's a limitation of the Omni sensor and I never really cared enough to look beyond that explanation. I've always just gone by what my actual boost gauge says for vacuum.
#264
Newbie
Idk about the AEM, but I've never seen the Omni 4 bar show the correct values for vacuum in Evoscan. I've heard others say that it's a limitation of the Omni sensor and I never really cared enough to look beyond that explanation. I've always just gone by what my actual boost gauge says for vacuum.
#267
Is it still correct to disable to P0069 DTC on ROM 88590015. I just changed to omni 4 bar from stock and threw this code. Is it not possible to adjust the MAF setting so that they correspond to the new MAP sensor? Any known issues in disabling the code?
#269
Hello everyone.
I need help here. I'm trying to use omni 4 bar map sensor in Evo 9 wagon Auto. I've created xml list below and found all MAP fault maps but MAP vs MAF Baro and MAP Comparison are different values to Evo9 and 8 roms listed by mrfred 162 and 4.00v
Anyone know what's the deal here?
<table name="MAP Scaling" category="MAP SENSOR" address="55cc" type="2D" level="1" scaling="uint8">
<table name="MAP Output" address="68c4" type="Y Axis" elements="9" scaling="Volts16"/>
</table>
<table name="MAP Fault Trig: Mid VE Max #1" category="MAP SENSOR" address="297e" type="1D" level="1" scaling="Volts16"/>
<table name="MAP Fault Trig: Mid VE Min #1" category="MAP SENSOR" address="295e" type="1D" level="1" scaling="Volts16"/>
<table name="MAP Fault Trig High VE #1" category="MAP SENSOR" address="2964" type="1D" level="1" scaling="Volts16"/>
<table name="MAP vs MAF Baro" category="MAP SENSOR" address="283c" type="1D" level="1" scaling="uint16"/>
<table name="MAP Comparison" category="MAP SENSOR" address="2838" type="1D" level="1" scaling="Volts16"/>
I need help here. I'm trying to use omni 4 bar map sensor in Evo 9 wagon Auto. I've created xml list below and found all MAP fault maps but MAP vs MAF Baro and MAP Comparison are different values to Evo9 and 8 roms listed by mrfred 162 and 4.00v
Anyone know what's the deal here?
<table name="MAP Scaling" category="MAP SENSOR" address="55cc" type="2D" level="1" scaling="uint8">
<table name="MAP Output" address="68c4" type="Y Axis" elements="9" scaling="Volts16"/>
</table>
<table name="MAP Fault Trig: Mid VE Max #1" category="MAP SENSOR" address="297e" type="1D" level="1" scaling="Volts16"/>
<table name="MAP Fault Trig: Mid VE Min #1" category="MAP SENSOR" address="295e" type="1D" level="1" scaling="Volts16"/>
<table name="MAP Fault Trig High VE #1" category="MAP SENSOR" address="2964" type="1D" level="1" scaling="Volts16"/>
<table name="MAP vs MAF Baro" category="MAP SENSOR" address="283c" type="1D" level="1" scaling="uint16"/>
<table name="MAP Comparison" category="MAP SENSOR" address="2838" type="1D" level="1" scaling="Volts16"/>
Thread
Thread Starter
Forum
Replies
Last Post
2006, 31, bar, byte, difference, evo, evolution, lancer, launch, logreference, map, mitsubishi, mitsulogger, omni, sensor