2006_RA

iTrader: (1)

The pads will fit.

The discs are 0.7 inches larger in diameter. You would need :
MR307282 bracket for the caliper to use 11.6 inch front discs.

Calipers and brackets from a 2005 Outlander would work too.

roblaza

iTrader: (22)

Now do it and post a How-To with muchos Picas

NorCal Lancer

iTrader: (1)

In case you were trying to buy some new rotors but needed to know the size, this image was taken from the centric site. Sizes are shown as the last 4 on the bottom. Just ordered a set through Amazon so I can be tax free and free 6 month financing with my store card.

VCRalliart

I'm looking to upgrade the calipers on my 04ralliart I found a set off a 95 gsx... I read that the front are direct bolt on. How about the rear?? And will I have to replace the lines??

nekkidlad

iTrader: (4)

https://www.evolutionm.net/forums/04...brake-evo.html
look here, it talks about the swap from evos and dsms(eclipse)

MichaelHaley

So I am confused about this whole fitment of rims after reading this whole article. My question is pretty simple for you guys that understand this. Will 18x8 +45 offset fit on my 05 RA. Its on Tein coilovers and was thinking of running anywhere from 205 35r18 - 225 35 r18....

RacerX-Ralliart

iTrader: (3)

Ebc yellow stuff pads painted black with ebc usr rotors and I also painted the calipers emerald green.



I wish they would stay black..

CrAnSwIcK

iTrader: (5)

looks expensive...the colors look nice, especially the green caliper and black bracket...

I have red calipers and brackets...just got Hawk HPS pads all around and some generic centric rotors for them to chew up

RacerX-Ralliart

iTrader: (3)

Thank you! The bracket was supposed to be gloss black but I only had flat.. O well.. I wanted good quality rotors up front because my last pair warped and I was real tired of the steering wheel shimming when stepping on the brakes I have professional grade raybestos pads and rotors to fit in the back that I bought when I used to work at the parts store..

mikemike396

iTrader: (3)

Do you have model numbers for the pads and rotors you have in the front?

Looks like these rotors and pads?
http://ebcrotors.com/p-224-ebc-ultimax-rotors.aspx
http://ebcrotors.com/p-221-ebc-yello...rake-pads.aspx

RacerX-Ralliart

iTrader: (3)

Pads are dp41614r and the rotors part number USR7104 I bought them off amazon cause I have prime which gave me free 2 day shipping

2006_RA

iTrader: (1)

I hope your experience with the USR7104's is better than mine because for what they cost they didn't last for sh---.
I bought the cheapest discs I could find after.

RacerX-Ralliart

iTrader: (3)

When you say they didn't last do you mean they were below the minimum thickness? After how many miles? What kind of pads? I love the bite of the yellow stuff pads I barely have to press my pedal down to come to a full stop.. I'm still bedding them in another 100 miles than I will do the second bed in step..

2006_RA

iTrader: (1)

I used them with EBC Redstuff and they ended up warped like how you described earlier.

RacerX-Ralliart

iTrader: (3)

How many miles did you drive on them? This would be the second performance rotors I tried.. I tried power stop drilled and slotted rotors and hated them the growled at high speeds.. My raybestos rotors took a beating I got 25k miles out of them if I could get 35k out of the usrs I'll be happy

O and they are very good at resisting rust I washed my car yesterday and the front rotors had no rust and the rear was covered...