ECUFlash / Evoscan / Mitsulogger Questions
#286
if the baud rate is to high or low could i possibly change it to where it needs to be without anything bad happening and why would this change it was working fine then i closed the program then reopend and tried to read again and then it just started doing that and no i didnt flash or anything just closed out evoscan. BTW thanks for the input already.
#288
Evolved Member
iTrader: (22)
The text box actually just needs a stray number to go in there and it will remember it. It really should display as a read-only box and only if someone clicks on some hard button (change baud rate) then should it allow itself be edited. I seem to remember debug mode for Wideband also changing the value but oh well just watch out for it in future.
#289
Evolving Member
iTrader: (5)
Join Date: May 2005
Location: Chester Springs, PA
Posts: 114
Likes: 0
Received 0 Likes
on
0 Posts
How can you capture "2-byte Load" using MitsuLogger? Does anyone know how to alter registerID.xml to make it work?
MJ had it on other thread: Add below to the MitsuLogger registerID.XML file
----------------------
<Request LogReference="requestID00" RequestID="00" Eval="x" Unit="INT" Logged="y" Response="2"/>
<Request LogReference="requestID01" RequestID="01" Eval="x" Unit="INT" Logged="y" Response="2"/>
<Request LogReference="2ByteLoad" RequestID="FF" Eval="((256*requestID00)+requestID01)*10/32" Unit="2byteLoad" Logged="y" Response="2"/>
Also, don't forget the 2-byte load setup on other thread where you need to flash your ECU with different set of number...
MJ had it on other thread: Add below to the MitsuLogger registerID.XML file
----------------------
<Request LogReference="requestID00" RequestID="00" Eval="x" Unit="INT" Logged="y" Response="2"/>
<Request LogReference="requestID01" RequestID="01" Eval="x" Unit="INT" Logged="y" Response="2"/>
<Request LogReference="2ByteLoad" RequestID="FF" Eval="((256*requestID00)+requestID01)*10/32" Unit="2byteLoad" Logged="y" Response="2"/>
Also, don't forget the 2-byte load setup on other thread where you need to flash your ECU with different set of number...
Last edited by DanInPA; Aug 11, 2007 at 08:37 PM.
#290
Evolved Member
iTrader: (12)
Join Date: Jun 2006
Location: SJ, CA
Posts: 577
Likes: 0
Received 0 Likes
on
0 Posts
anyone log both a ZT2 and evoscan at the same time (err, meaning using the WB input of evoscan)? Im using a serial to usb adapter (COM 5), but when I try to log via evoscan it doesnt work, get a "unable to open port" error, or the signal get get fubared and it wont log at all
any ideas?
any ideas?
#296
Evolving Member
This question pertains to Evoscan 1.0 Alpha.
Today I logged a Lancer Evolution VII GSR. Everything logged fine except 2Byte Load:
Why are the readings so off? The car was feeling down on power but I didn't see anything wrong in the logs.
Here is a copy of the log for assistance: http://download.yousendit.com/7E27787E72F994B4
Today I logged a Lancer Evolution VII GSR. Everything logged fine except 2Byte Load:
Why are the readings so off? The car was feeling down on power but I didn't see anything wrong in the logs.
Here is a copy of the log for assistance: http://download.yousendit.com/7E27787E72F994B4
Last edited by R. Mutt; Aug 22, 2007 at 05:50 PM. Reason: added copy of datalog
#297
Evolving Member
iTrader: (2)
problem with evoscan:
Was using it to log WB with my LC-1...unclicked it last night (cause i didnt feel like connecting the LC-1 to the laptop) to do some timing tuning.
When i clicked back on the WB, it only reads 1-5v...not the actual AFR's anymore.
I didnt change anything in the .xml.
The LC-1 still works fine with all the other programs, Logworks, Mitsulogger, etc...
p.s. using Evoscan v.99
Was using it to log WB with my LC-1...unclicked it last night (cause i didnt feel like connecting the LC-1 to the laptop) to do some timing tuning.
When i clicked back on the WB, it only reads 1-5v...not the actual AFR's anymore.
I didnt change anything in the .xml.
The LC-1 still works fine with all the other programs, Logworks, Mitsulogger, etc...
p.s. using Evoscan v.99
Last edited by SoCalRedLine; Aug 24, 2007 at 10:17 AM.
#298
Evolving Member
iTrader: (2)
I found a few threads that address the same problem...but i already checked gas type, and its set on Gasoline. The LC-1 works fine with Logworks.
https://www.evolutionm.net/forums/sh...n+LC-1+problem
https://www.evolutionm.net/forums/sh...56#post3842556
https://www.evolutionm.net/forums/sh...n+LC-1+problem
https://www.evolutionm.net/forums/sh...56#post3842556