Evoscan2.0 is out
I had to mess around with my def a bit but I got it working. Thanks for the help.
Although, I'm still unable to get the port selection tab on wideband to open up.
I also noticed a bug - if you have the map tracer open, and you hit alt+tab to switch windows, when you switch back the data in the bottom part of the map tracer has changed and no longer reflects the data in the map. You have to right click and select the map again to get the proper data back.
- It would be awesome if you could actually adjust the values in the map as they are shown on the bottom section of the map tracer.
Although, I'm still unable to get the port selection tab on wideband to open up.
I also noticed a bug - if you have the map tracer open, and you hit alt+tab to switch windows, when you switch back the data in the bottom part of the map tracer has changed and no longer reflects the data in the map. You have to right click and select the map again to get the proper data back.
- It would be awesome if you could actually adjust the values in the map as they are shown on the bottom section of the map tracer.
Originally Posted by in Evoscan Map Tracer Link by: Hamish
In a future version of EvoScan the bottom grid with the ROM data will be made directly editable.
I'm going to try with out the usb adapter and connect to com1(old school serial).
I must be doing something wrong because the map tracer is not working for me. Will this only work with logs taken via 2.0 maptracer edition? I have to sets of logs from 2.0 only and do not get anything on the tracer. When I use the ROMID XML and my HEX file and check timing advanced I get 60 in the load 10 cell in the top left corner. ANy thoughts?
Just downloaded...haven't installed it yet. Saved my old data.xml...is the new data.xml similiar to the old .99 version? I have a bunch of custom stuff I will have to move over to the new one I would imagine.
Anyone had any issues so far with using custom data.xml with v2.0?
Anyone had any issues so far with using custom data.xml with v2.0?
Just downloaded...haven't installed it yet. Saved my old data.xml...is the new data.xml similiar to the old .99 version? I have a bunch of custom stuff I will have to move over to the new one I would imagine.
Anyone had any issues so far with using custom data.xml with v2.0?
Anyone had any issues so far with using custom data.xml with v2.0?
Thanks. I'll windiff it to 0.99 whenever I install it and see I guess. I prefer to deal with the xml straight up . So any other issues other than the non-selectable comport for wideband (holding off because of this I need my AFRs!!!)?
. So any other issues other than the non-selectable comport for wideband (holding off because of this I need my AFRs!!!)?
Last edited by codgi; Nov 21, 2007 at 12:38 AM.
You can install the versions side by side.. there is no requirement to uninstall the previous version of EvoScan.
There was some new ComPort detection code I did for the wideband com port, i will change it back.
If your hex/xml file doesn't load in MapTracer, email it to me evoscan@limitless.co.nz and I'll check it out
yes, I am currently testing the editable cells in the rom file as mentioned above.
yes, great idea about highlighting the corresponding cells in the map tracer. (and I'll also check that the less than/greater than, and correct cells are being loaded. Let me know if you think its out by one cell.
I think I will apply an AFR data log conversion to 14.7AFR representation too.
There was some new ComPort detection code I did for the wideband com port, i will change it back.
If your hex/xml file doesn't load in MapTracer, email it to me evoscan@limitless.co.nz and I'll check it out
yes, I am currently testing the editable cells in the rom file as mentioned above.
yes, great idea about highlighting the corresponding cells in the map tracer. (and I'll also check that the less than/greater than, and correct cells are being loaded. Let me know if you think its out by one cell.
I think I will apply an AFR data log conversion to 14.7AFR representation too.
You can install the versions side by side.. there is no requirement to uninstall the previous version of EvoScan.
There was some new ComPort detection code I did for the wideband com port, i will change it back.
If your hex/xml file doesn't load in MapTracer, email it to me evoscan@limitless.co.nz and I'll check it out
yes, I am currently testing the editable cells in the rom file as mentioned above.
yes, great idea about highlighting the corresponding cells in the map tracer. (and I'll also check that the less than/greater than, and correct cells are being loaded. Let me know if you think its out by one cell.
I think I will apply an AFR data log conversion to 14.7AFR representation too.
There was some new ComPort detection code I did for the wideband com port, i will change it back.
If your hex/xml file doesn't load in MapTracer, email it to me evoscan@limitless.co.nz and I'll check it out
yes, I am currently testing the editable cells in the rom file as mentioned above.
yes, great idea about highlighting the corresponding cells in the map tracer. (and I'll also check that the less than/greater than, and correct cells are being loaded. Let me know if you think its out by one cell.
I think I will apply an AFR data log conversion to 14.7AFR representation too.
What about the one other bug I noticed. When you use alt+tab to switch windows while the map tracer is open, all the data on the bottom portion is changed once you alt+tab back to that window.
when i went out this morning to test out evoscan v2 i tried to log and for loadcalc it read out as -infinity and 2byte load read out as 35. can one of you guys tell me what is wrong?
